Atwood SCALE-O-MATIC S302, Operation And Safety Manual

Page: 11 / 53

AM MFG. CO. MASTER MODEL:
DIV. OF ATWOOD CORP. S302
© 2011
S302_9 9 1/11
ROUNDER CLEANING PROCEDURES
THESE PROCEDURES ARE VERY IMPORTANT TO MAINTAIN
PRODUCT QUALITY AND MACHINE PERFORMANCE.
II. ROUNDER
A. DANGER: SHUT OFF ALL ELECTRICAL POWER.
B. REMOVE DIVIDER SLIDE GUARD BY LOOSENING (2) HEX HEAD NUTS (ASSUMING THE GUARD IS NOT ALREADY
REMOVED)
C. OPEN AND TILT FRONT OF ROUNDER
D. LIFT HANDLE ON SMALL INSPECTION DOOR SIDE.
E. TILT ROUNDER ASSEMBLY FORWARD.
F. REMOVE FUNNEL (PART NO. R116RA ).
G. REMOVE ROUNDER SCREW (PART NO. R122RA)
1. DO NOT DROP OR SET DOWN ON SCREW STEM (THIS CAN MUSHROOM THE STEM SO THAT THE SCREW WILL
NOT RE-ENTER BASE). IT IS RECOMMENDED THAT THE SCREW BE LAID ON ITS SIDE. BEWARE NOT TO BUMP
THE OUTER EDGE (WHICH IS NICKEL COATED) AS THIS CAN CAUSE FLAKING OF THE NICKEL OR STAND IT
UPRIGHT ON THE OPPOSITE SIDE OF THE STEM.
2. THE SCREW SHOULD BE CLEANED WITH WARM WATER AND A NON-ABRASIVE PAD. REMOVE ALL DRIED
DOUGH FROM THE EDGE AND ROUNDING SURFACE WITH A PLASTIC SCRAPER IF NEEDED. DRY COMPLETELY.
3. DO NOT PLACE IN AN AUTOMATIC DISHWASHER
A. REMOVE DRUM (PART NO. R117RA)
1. TAKE THE DRUM OUT OF THE MACHINE: DO NOT LAY DRUM ON ITS SIDE (THIS CAN CAUSE WARPING OF THE
DRUM, WHICH WILL NOT ALLOW THE DRUM AND SCREW TO FIT TOGETHER). IT IS RECOMMENDED THAT THE
DRUM BE STOOD ON END.
2. THE DRUM SHOULD BE CLEANED WITH WARM WATER (WATER TEMP. SHOULD NOT EXCEED 190°F) AND A NON-
ABRASIVE PAD (PLASTIC BRISTLE BRUSH RECOMMENDED). REMOVE ALL DRIED DOUGH FROM THE GROOVED
AND INNER SURFACE OF THE DRUM. DRY COMPLETELY.
3. DO NOT PLACE IN AN AUTOMATIC DISHWASHER (THIS, TOO, CAN CAUSE WARPING OF THE DRUM WHICH
WOULD NOT ALLOW THE DRUM AND SCREW TO FIT TOGETHER).
A. REMOVE PLASTIC SEAL RING (PART NO. 141RA).
B. REMOVE EXCESS DOUGH FROM ROUNDER BASE.
C. REASSEMBLY IS REVERSE OF DISASSEMBLY.
D. MAKE SURE TO REPLACE PLASTIC SEAL RING.
E. SLIP THE DRUM OVER THE ROUNDER BASE SO THAT THE DRIVE SLOTS ARE LOCKED OVER THE DRIVE PINS IN THE
ROUNDER BASE.
F. CARE SHOULD BE TAKEN TO SEE THAT THE EXIT RAMP ON THE SCREW IS FACING DISCHARGE END OF MACHINE.
G. TILT ROUNDER ASSEMBLY BACKWARD AND LOCK IN PLACE.
H. WIPE EXCESS DOUGH FROM CONVEYOR BELT AND AREA AROUND ROUNDER.
II. NOTES
ALL PARTS AND AREAS MENTIONED MUST BE CLEANED EVERY DAY.
IF UNABLE TO REMOVE ROUNDER SCREW:
A. PLUG MACHINE IN, TURN MACHINE ON.
B. ADD A SMALL AMOUNT OF WARM WATER TO CONTACT AREA BETWEEN SCREW AND DRUM.
C. AFTER DOUGH SOFTENS, TURN OFF ROUNDER.
D. UNPLUG MACHINE.
E. REMOVE ROUNDER SCREW.
**
IF THE SCREW CAN’T BE REMOVED CALL AM MANUFACTURING FOR ASSISTANCE.
PRACTICE SAFETY FIRST:
ALWAYS DISCONNECT ELECTRICAL SERVICE WHEN CLEANING OR MAINTAINING THIS MACHINE, THUS AVOIDING CHANCE OF
SERIOUS INJURIES. MACHINES ARE NOT DANGEROUS IF COMMON SENSE IS APPLIED AND THE INSTRUCTIONS ARE
CAREFULLY FOLLOWED. THINK AND PRACTICE SAFETY FIRST.