background image

Chill V Series

7. Maintenance

7.1  Cleaning

 

•  Before cleaning the equipment,  

remove the main plug.

 

•  The unit can be cleaned with water 

with the addition of a few drops of a 
detergent (washing-up liquid), using a 
moist cloth.

 

•  Water must not enter the control unit

 

•  The user is responsible for carrying out an appropriate detoxification of any 

dangerous material which has been spilled on or in the unit. This applies in 
particular when the unit is passed on to someone else for operation, repair, 
storage etc.

7.2  Maintenance of the refrigeration unit 

 

•  The refrigeration unit operates largely 

maintenance-free. If the unit is being operated 
in a dusty atmosphere the condenser of the 
refrigerator has to be cleaned at intervals of 4 to 
6 months or more frequently. This is best done 
by blowing compressed air or nitrogen into the 
ventilation openings for a few minutes

 

•  It may be useful to unscrew the grill. This can 

be done in a most suitable way by screwing off 
the ventilation grid, then cleaning the condenser 
with a vacuum cleaner (using the brush-top).

7.3 Repair and disposal instructions

 

•  The refrigeration unit is filled with refrigerant. 

Repair and disposal must only be carried out by a qualified refrigeration technician.

 

•  Before you return the equipment for servicing it is advisable to contact our 

Technical Service department.

 

•  If the equipment has to be returned to the factory, please ensure that it is  

carefully and properly packed. We accept no responsibility for damage  
due to unsatisfactory packing.

Summary of Contents for Chill V Series













Reviews: