manualshive.com logo in svg

Atop SE5002D-Fm, User Manual

Share
Download
Atop SE5002D-Fm User Manual Download Page 75

Atop Serial Device Server 

SE5002D 

User Manual V. 1.1

 

 

 

4.4 

Using Serial/IP port Monitor 

4.4.1 

Opening the Port Monitor   

The Serial/IP Port Monitor can be opened by: 

 

Start

→

All Programs

→

Serial/IP 

→

Port Monitor 

 

Double click the Serial/IP tray icon in the Windows notification area.   

 

In the Windows notification area (

Fig. 4. 3

), right click on the Serial/IP tray icon and click 

on 

Port Monitor

 to open the

 Port Monitor.

   

 

Click on the 

Port Monitor 

button in the Serial/IP Control Panel. 

 

4.4.2 

The Activity Panel 

 

 

Fig. 4. 14

 

 

The Activity panel provides a real-time display of the status of all Serial/IP COM ports (

Fig. 4. 

14

). If the Virtual COM Port is open and is properly configured to connect to a serial device 

server, the status would be 

Connected. 

If Serial/IP cannot find the specified serial device server, 

the status would be 

Offline

. 

 

 

 

Summary of Contents for SE5002D-Fm
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands