manualshive.com logo in svg

Atop SE5002D-Fm, User Manual

Share
Download
Atop SE5002D-Fm User Manual Download Page 63

Atop Serial Device Server 

SE5002D 

User Manual V. 1.1

 

 

 

 

4.1.2 

Limitation   

The Virtual COM driver allows up to 256 

Virtual COM ports

 in a single PC. Selecting in the 

range  from  COM1  to  COM4096  is  allowed.  Note  that  COM  ports  already  occupied  by  the 

system or other devices will not be available.   

 

4.1.3 

Installation   

Run the Virtual COM setup file included in the CD or download a copy from our website to install 

the  Virtual  COM  driver  for  your  OS.  Turn  off  your  antivirus  software  and  try  again  if  the 

installation fails. At the end of the installation, please select at least one Virtual COM port from 

the Serial/IP Control Panel.   

 

4.1.4 

Uninstalling 

 

From Windows Start Menu, select Control Panel, Add/Remove Programs. 

 

Select 

Serial/IP Version x.x.x

 in the list of installed software.   

 

Click the 

Remove

 button to remove the program. 

 

 

 

Summary of Contents for SE5002D-Fm
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands