manualshive.com logo in svg

Atop EH3408ls, User Manual

Share
Download
Atop EH3408ls User Manual Download Page 44

Industrial Managed  
Ethernet Switch 

User Manual 

Configuring

  with  a  Web 

Browser 

 
 

Page 

44

 of 

49

 

 

2.8.3

 

Backup/Restore (storage device) feature 

The Backup/Restore (storage device) feature under the Maintenance function is an alternative feature that allows the 
user  to  backup  or  restore  configuration  file  to  or  from  the  storage  device  inside  the  EH3408  chasis.  Note  that 
Backup/Restore feature in previous subsection download or load the configuration file to and from the local host 
computer. The storage device can be a Micro-SD card (for EH3408ls and EH3408s) or USB storage device (EH3408lu 
and EH3408u) attached to the EH3408 device. The supported formats of the storate device are FAT32 and exFAT.  

 

 

Figure 2.57 Backup/Restore (storage device)  

 

To setup the automatic backup, the user can click the gear icon next to 

the Storage Auto Backup

 to bring up the pop-

up window as shown in Figure 2.58 for EH3408lu and EH3408u or as shown in Figure 2.59 for EH3408ls and EH3408s. 
There  are  two  options  on  this  window  which  are 

Sync  backup

  and 

Backup  frequency

.  After  finished  setting  the 

options, click on the 

Save

 button.  

 

 

Figure 2.58 USB Auto Backup Pop-up Window for EH3408lu and EH3408u 

 

 

Summary of Contents for EH3408ls


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands