ATN Zebra 12 Operator'S And Safety Manual Download Page 15 | Manualshive

Page: 15 / 45

background image

OPERATOR AND SAFETY MANUAL

1NO0027UK-05

ZEBRA 12

15

DANGER

RISK OF CRUSHING

-  THERE  IS  A  RISK  OF  SEVERE,  EVEN  LETHAL,  INJURIES  IN  CASE  OF  CRUSHING  OR
SHOCK  WITH  THE  PLATFORM  WITH  AN  OBSTACLE  OR  WHEN  CONTROLLING  THE
MACHINE.
- AVOID ANY CONTACT OF THE PLATFORM WITH AN OBSTACLE.
- DO NOT BRING THE PLATFORM IN CONTACT WITH OBSTACLES IN HIGH LOCATIONS.
- DO NOT LOWER THE PLATFORM ON OBSTACLES OR STAFF LOCATED UNDER IT.
-  DO  NOT  ACTUATE  THE  TURRET  IN  THE  PRESENCE  OF  OBSTACLES  OR  STAFF
AROUND THE MACHINE.
- CHECK THAT THE STAFF IS AT SUFFICIENT DISTANCE.
- ALWAYS CONSIDER THE MACHINE'S ENVIRONMENT WHEN MOVING OR ANY OTHER
MANOEUVRE.

DANGER

RISK OF ELECTRIC SHOCK: THIS MACHINE IS NOT ISOLATED

- THERE IS A RISK OF SEVERE, EVEN LETHAL, INJURIES IN CASE OF INSUFFICIENT
DISTANCE BETWEEN LIVE POWER LINES AND THE MACHINE.
- NEVER USE THE MACHINE IN THE IMMEDIATE PROXIMITY OF LIVE POWER LINES OR
EQUIPMENT.
- NEVER USE THE MACHINE IN STORMY WEATHER.
- MAINTAIN A MINIMUM SAFETY DISTANCE OF 10 METRES WITH LIVE POWER LINES
OR EQUIPMENT.
- GROUND STAFF MUST STAY AWAY FROM THE MACHINE WHEN IT IS CLOSE TO LIVE
POWER LINES OR EQUIPMENT.

2.4. CRUSHING

HAZARD

You must be aware of your environment at all times when using the machine. You must see what
is below, above, on the side, in front or behind the platform during all movement, rotation,
translation, elevation or descent movements. When having a good view of the machine's
movement is impossible, ask another person to guide you from the ground.

2.5. ELECTRICAL

HAZARD

Before moving the platform under electric lines, ensure there is sufficient height.
In case of contact of the platform with an electric source, the operator must evacuate staff around
the machine. Never let anyone use the emergency control panel without authorization from the
operator. The operator must try to clear the machine using the controls located in the platform. If
the operator cannot clear the platform, the power source must be

powered off

.

In case of contact with a live power source, after this incident, have the machine checked and if
required repaired by the manufacturer.

«
...
13
14
15
16
17
...
»

Summary of Contents for Zebra 12














































Reviews:

No comments

Related manuals for Zebra 12

Brand: POP UP Pages: 20

Brand: Torin Pages: 31

Brand: Atlas Pages: 29

Genie GTH-4020 ER

Brand: Terex Pages: 188

Brand: Terex Pages: 135

Genie Z-45/25 Bi-Energy

Brand: Terex Pages: 213

Brand: Terex Pages: 197

Brand: Autoquip Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands