Atlona AT-GAIN-60 Manual Download Page 11 | Manualshive

Page: 11 / 39

background image

AT-GAIN-60

11

Installation

RS-232

The AT-GAIN-60 provides RS-232 control between an automation system and an RS-232 device. This step is

optional.

1. Use wire strippers to remove a portion of the cable jacket.

2.

Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires.

3.

Insert the TX, RX, and GND wires into correct terminal on the included captive screw block.

GND

RX

TX

5

3

2

«
...
9
10
11
12
13
...
»

Summary of Contents for AT-GAIN-60








































Reviews:

No comments

Related manuals for AT-GAIN-60

Brand: Maintronic Pages: 4

Brand: Vanguard Dynamics Pages: 3

Brand: Wyred 4 Sound Pages: 12

Brand: JBL Pages: 28

Brand: Inter-m Pages: 20

Brand: McIntosh Pages: 20

Brand: ELECTROCOMPANIET Pages: 8

Brand: Summit Audio Pages: 20

TABU AT INTEGRATED AMPLIFIER

Brand: Gryphon Pages: 6

Brand: Redback Pages: 4

Brand: Jolida Pages: 17

Brand: Karak Electronics Pages: 13

Brand: Velleman-Kit Pages: 16

Brand: Ovation Pages: 2

Brand: Senrun Pages: 16

Brand: McIntosh Pages: 32

Brand: National Instruments Pages: 14

Brand: Tascam Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands