22
The connector of the connection cable must be splash-proof.
When running the
connection line
observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Do not use the
cable
for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges
. Do
not use the cable to pull the plug from the socket.
Regularly check the
extension cables
and replace them if
they are damaged.
Do not use any
defective connection cables
.
When working outdoors, only use extension cables especially
approved
and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections
.
Never bypass
protective devices or deactivate them.
The
electrical connection
or
repairs
to electrical parts of
the machine must be carried out by a certified electrician or
one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs
to other parts of the machine must be carried out
by the
manufacturer
or one of his customer service points.
Use only original
spare parts. Accidents can arise for the
user through the
use of other spare parts
. The
manufacturer is not liable for any damage
or injury resulting
from such action.
A
A
s
s
s
s
e
e
m
m
b
b
l
l
y
y
⇒
see page 144
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
Move the splitting blade right down every time before the
machine is transported.
To transport the
machine, grasp the
handle and tilt the log
splitter slightly towards
you. The log splitter
can be easily
transported in this
position.
P
P
o
o
s
s
i
i
t
t
i
i
o
o
n
n
i
i
n
n
g
g
Ensure that the working area meets the following conditions:
−
no danger of slipping
−
level
−
free of obstacles
−
sufficiently well lit
Do not operate the machine in the direct vicinity of gas
or petrol pipes or containers, or any other easily inflammable
materials.
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Check
that the machine is completely and correctly
assembled.
Before using the log splitter
, make sure each time that
−
there are no faulty connections (tears, cuts, etc.)
Do not use defective power supply cables.
−
there are no damages at the machine
−
all screws are tight
−
check the hydraulic system for any possible leaks
−
the oil level
L
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to the
relevant and properly earthed plug.
Only use
connection cables
with sufficient cross-sections.
Connect the machine via a 30 mA fault current safety switch.
L
Fuse protection
400 V 3~
Î
16 A
L
Switching on / off
Prior to every use, check the function of the disconnection
mechanism (by switching on and off).
Do not use any device where the switch can not be switched
on and off. Damaged switches must be repaired or replaced
immediately by the customer service.
Switching on
Press the green button.
Switching off
Press the red button.
L
Lock in case of power (zero-voltage
initiator)
The equipment will switch off automatically if there is a power cut.
Repress the green button to switch it on again.
Log splitter with 400 V 3~
Make sure that the motor turns in the
correct direction (see motor arrow), because operation in the
wrong direction damages the oil pump.
¾
Switch on motor; the splitting blade automatically moves to the
highest position.
¾
If the splitting blade is already in its highest position: grip both
operating handles and push them down. The splitting blade
moves downwards.
¾
If the splitting blade does not move after the motor has started,
switch off the motor and change the direction of rotation.
transport belt
