AT&T SynJ SB67158 User Manual Download | Manualshive

Page: 105 / 116

background image

If you have difficulty with your telephone, please try the following suggestions.
For customer service, visit our website at

www.telephones.att.com

or

call

1 (888) 915-2007

. In Canada, dial

1 (866) 288-4268

.

My telephone base doesn’t work at all.

Make sure the power cord is securely plugged in.
Make sure you plug the telephone line cord securely and firmly into the
telephone base and the telephone wall jack.
Reset the telephone base. Unplug the electrical power. Wait approximately
15 seconds, then plug it back in. Allow up to one minute for the telephone
base to reset.
Other electronic products such as HAM radios and other DECT phones, can
cause interference with your cordless phone. Try installing your phone as
far away as possible from these types of electronic devices.
You may need to purchase four AA alkaline batteries as backup battery to
make the telephone base work in the event of a power failure. Please refer
to

Optional

backup battery installation

on page 9 in this user’s manual.

I cannot get a dial tone from the corded handset.

First try all the suggestions, as mentioned above.
Make sure you plug the handset cord securely and firmly into the

HANDSET

jack on the telephone base and the corded handset.

If the previous suggestions do not work, disconnect the telephone base
from the telephone jack and connect to a different telephone. If there is
no dial tone on that telephone either, the problem is in your wiring or local
service. Contact your telephone service provider.
Your line cord might be malfunctioning. Try installing a new line cord.

I cannot dial out.

First try all the suggestions, as mentioned above.
Make sure you have a dial tone before dialing. The corded handset might
take a second or two to connect the telephone base and produce a dial
tone. This is normal. Wait an extra second before dialing.
Eliminate any background noise. Noise from a television, radio or other
appliances might cause the telephone to not dial out properly. If you
cannot eliminate the background noise, first try muting the corded handset
before dialing, or dialing from another room by a cordless handset with less
background noise.
If the other telephones in your building are having the same problem,
contact your telephone service provider.

•
•

•

•

•

•
•

•

•

•
•

•

•

Appendix

Troubleshooting

99

«
...
103
104
105
106
107
...
»

Summary of Contents for SynJ SB67158





















































































































Reviews:

No comments

Related manuals for SynJ SB67158

Brand: NEC Pages: 334

Brand: NEC Pages: 12

Brand: Uniden Pages: 44

Brand: Olympia Pages: 28

Brand: PhoneMate Pages: 24

Brand: Radio Shack Pages: 32

Brand: Yealink Pages: 347

Brand: GE Pages: 48

Brand: Karel Pages: 81

Brand: AT&T Pages: 15

Brand: DAINCUBE Pages: 35

Brand: Profoon Pages: 12

Brand: VTech Pages: 39

Brand: Panasonic Pages: 84

Profiset 70isdn

Brand: Siemens Pages: 118

Brand: Siemens Pages: 151

SPP-A2780 - 2.4ghz Cordless Telephone

Brand: Sony Pages: 2

SPP-A2770 - 2.4ghz Cordless Telephone

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands