Asus Maximus iv extreme rev 3 User Manual Download Page 118

Page: 118 / 196

3-26

Chapter 3: BIOS setup

SPDIF Out Type [SPDIF]

[SPDIF]

Set the SPDIF OUT mode to SPDIF.

[HDMI]

Set the SPDIF OUT mode to HDMI.

Renesas USB 3.0 Controller [Enabled]

[Enabled]

Enables the USB 3.0 controller.

[Disabled]

Disables the controller.

Intel 82583 LAN [Enabled]

[Enabled]

Enables the Intel 82583 LAN controller.

[Disabled]

Disables the controller.

Intel 82583 PXE OPROM [Disabled]

This item appears only when you set the previous item to [Enabled] and allows you

to enable or disable boot option for Legacy Network Devices.

Configuration options: [Enabled] [Disabled]

Marvell Storage Controller [AHCI]

Allows you to select the Marvell storage controller operating mode.
[Disabled]

Disables the controller.

[IDE]

Set to [IDE] when you want to use the Serial ATA hard disk drives

as Parallel ATA physical storage devices.

[AHCI]

Set to [AHCI] when you want the SATA hard disk drives to use the

AHCI (Advanced Host Controller Interface). The AHCI allows the

onboard storage driver to enable advanced Serial ATA features that

increases storage performance on random workloads by allowing

the drive to internally optimize the order of commands.

[RAID]

Set to [RAID] when you want to create a RAID configuration from

the SATA hard disk drives.

Marvell Storage OPROM [Enabled]

This item appears only when you set the previous item to [Enabled] and allows you

to enable or disable the OptionRom of the Marvell storage controller.

Configuration options: [Enabled] [Disabled]

JMB Storage Controller [Enabled]

Allows you to enable or disable the JMB storage controller.

Configuration options: [Disabled] [Enabled]

If you want to use the full functin of the JMB storage contorller (ex. AHCI), we

recommend that you set this item to [Enabled] and install the

JMicron JMB36X

Controller Driver

from the motherboard support DVD.

Summary of Contents for Maximus iv extreme rev 3





































































































































































































Search results

Summary of Contents for Maximus iv extreme rev 3

Reviews:

Asus Maximus iv extreme rev 3, User Manual, Page: 118 / 196

Search results

Summary of Contents for Maximus iv extreme rev 3

Reviews: