Asus AAEON GENESYS-KBU6 User Manual Download

Page: 85 / 98

Chapter 4

–

Driver Installation

3.5

” S

mp
act

ard

ENE

S-

KBU6

4.1 Drivers Download and Installation

Drivers for the GENESYS-KBU6 can be downloaded from the product page on the

AAEON website by following this link:

https://www.aaeon.com/en/p/3-and-half-inches-subcompact-boards-GENESYS-kbu6

Download the driver(s) you need and follow the steps below to install them.

Step 1

–

Install Chipset Drivers

Open the

Step1 - Chipset

folder followed by SetupChipset.exe

Follow the instructions

Drivers will be installed automatically

Step 2

–

Install Graphics Drivers

Open the Step2 - Graphic

folder followed by

Setup.exe

Follow the instructions

Drivers will be installed automatically

Step 3

–

Install LAN Drivers

Click on the Step3 - LAN folder and select your OS

Open the.exe file in the folder

Follow the instructions

Drivers will be installed automatically

Step 4

–

Install Audio Drivers

Open the Step4 - Audio folder followed by Setup.exe

Follow the instructions

Drivers will be installed automatically

Summary of Contents for AAEON GENESYS-KBU6



































































































Search results

Summary of Contents for AAEON GENESYS-KBU6

Reviews:

Related manuals for AAEON GENESYS-KBU6

Brands by name

Popular brands

Asus AAEON GENESYS-KBU6, User Manual

Search results

Summary of Contents for AAEON GENESYS-KBU6

Reviews:

Related manuals for AAEON GENESYS-KBU6

Brands by name

Popular brands