Asus AAEON GENESYS-KBU6 User Manual Download

Page: 47 / 98

Chapter 2

–

Hardware Information

3.5

” S

mp
act

ard

ENE

S-

KBU6

Step 3: Remove the clear backing from the large thermal pad and place onto the drive,

gently pushing down to adhere to the drive. Then, remove the backing from the

exposed side.

Step 4: Line up the large hole on the drive bracket with the VESA mount post on the

bottom panel. Make sure the holes are lined up for the screws. Attach the adhesive

backed mount to the bottom panel, then secure cables to the mount with a zip tie.

Secure the assembly with screws. Note: Screws attach through the bottom panel side.

Step 5: Attach the SATA cable to the board SATA connector (CN14). Then attach the

SATA Power cable to the board +5V output connector (CN15). See Chapter 2.2 for

connector locations.

SATA Power

(CN15)

SATA Connector

(CN14)

Summary of Contents for AAEON GENESYS-KBU6



































































































Search results

Summary of Contents for AAEON GENESYS-KBU6

Reviews:

Related manuals for AAEON GENESYS-KBU6

Brands by name

Popular brands

Asus AAEON GENESYS-KBU6, User Manual

Search results

Summary of Contents for AAEON GENESYS-KBU6

Reviews:

Related manuals for AAEON GENESYS-KBU6

Brands by name

Popular brands