Asus AAEON GENESYS-KBU6 User Manual Download Page 58

Page: 58 / 98

Chapter 3

–

AMI BIOS Setup

3.5

”

mp
act

ard

ENE

S-

KBU6

3.4.2

Trusted Computing

Options Summary

Security Device
Support

Disable

Enable

Optimal Default, Failsafe Default

Enables or Disables BIOS support for security device.
O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be
available.
SHA-1 PCR Bank

Disable

Enable

Optimal Default, Failsafe Default

Enable or Disable SHA-1 PCR Bank
SHA256 PCR Bank Disable

Enable

Optimal Default, Failsafe Default

Enable or Disable SHA256 PCR Bank
Pending operation None

Optimal Default, Failsafe Default

TPM Clear

Schedule an Operation for the Security Device. NOTE: Your Computer will reboot
during restart in order to change state of Security Device.

Summary of Contents for AAEON GENESYS-KBU6



































































































Search results

Summary of Contents for AAEON GENESYS-KBU6

Reviews:

Related manuals for AAEON GENESYS-KBU6

Brands by name

Popular brands

Asus AAEON GENESYS-KBU6, User Manual

Search results

Summary of Contents for AAEON GENESYS-KBU6

Reviews:

Related manuals for AAEON GENESYS-KBU6

Brands by name

Popular brands