ASM AllPro APB2525H Operating Instructions Manual Download | Manualshive

Page: 11 / 24

background image

11

309882

Spray tips have 4– or 5–digit numbers on them.
The first two digits are the spray angle. Tip
holding holes are provided on the chassis.

1. Perform

Pressure Relief Procedure,

page

6.

2. Point the gun and wand away from you and anyone else.

3. Lock trigger safety.

4. Without holding your hand over spray tip (A), pull back quick

coupler ring (B). Remove current tip. Install a different one.
Then push the ring back on.

Installing and Changing Spray Tips

Spray Tip
Number

Spray Pattern Fan Angle

00XXX

15XXX

25XXX

40XXX

Chemical

0

blaster (red)

15

(yellow)

25

(green)

40

(white)

XX

(black)

NOTE:

The chemical injector tip is brass and has a large opening and a black plastic cap.

B

A

To avoid blowing the o–ring out of the
quick coupler due to the high pressure in
the system, never operate pressure
washer without a tip securely mounted in
quick coupler.

CAUTION

«
...
9
10
11
12
13
...
»

Summary of Contents for AllPro APB2525H

























Reviews:

No comments

Related manuals for AllPro APB2525H

Brand: Haier Pages: 23

Brand: V-ZUG Pages: 8

Brand: Lavor Pages: 16

Brand: Lavor Pages: 108

INDEPENDENT 2000

Brand: Lavorwash Pages: 76

Brand: Simpson Pages: 44

Brand: Reaim Pages: 12

Brand: Make Cuisine Pages: 24

Brand: Indesit Pages: 16

Brand: Hotpoint Ariston Pages: 64

Brand: Ariston Pages: 36

Brand: Indesit Pages: 72

Brand: Parkside Pages: 50

Brand: LVO Manufacturing Pages: 34

Brand: ZANKER Pages: 20

Brand: Simpson Pages: 48

Brand: Panasonic Pages: 50

Brand: Frigidaire Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands