ASM AllPro APB2525H Operating Instructions Manual Download Page 5 | Manualshive

Page: 5 / 24

background image

5

309882

Shipping Damage

Check pressure washer for shipping damage.

Notify carrier immediately

if there is any damage.

Setup

Connect High–Pressure Hose and Gun

Connect high–pressure hose between the pump outlet and gun inlet.

Install Spray Tip

Install spray tip on wand. Installing and Changing Spray Tips,
page 11). If you are using a Sandblasting Kit, see its separate
manual for installation instructions.

Connect to Water Supply

Connect hose with at least a 3/4 in. (19 mm) ID from water supply
to 3/4 in. garden hose inlet on the pressure washer. The supply
hose should not be more than 50 ft (15 m) long.

Before you connect garden hose to pres-
sure washer, check local plumbing codes
regarding cross–connection to water
supply. If required, install backflow pre-
venter.

If inlet water pressure is over 60 psi (4.1
bar), a regulating water valve must be
installed at garden hose connection.

Do not exceed 104

°

F (40

°

C) inlet water

temperature.

CAUTION

Note:

Water source must have a minimum flow rate equal to that of pressure washer.

ti3228a

ti3229a

ti3457a

«
...
3
4
5
6
7
...
»

Summary of Contents for AllPro APB2525H

























Reviews:

No comments

Related manuals for AllPro APB2525H

Brand: Candy Pages: 30

Brand: R+M Suttner Pages: 8

Brand: ZEP Pages: 36

Brand: Kärcher Pages: 16

HD 7/250 DE TR1

Brand: Kärcher Pages: 20

Brand: Maytag Pages: 13

Brand: Ramteq Pages: 20

Brand: Gorenje Pages: 35

Brand: Ryobi Pages: 12

Brand: Ariston Pages: 60

HDS 3.0/20-4 EA/EG

Brand: Kärcher Pages: 48

Brand: Kärcher Pages: 196

Brand: McCulloch Pages: 7

Brand: Haier Pages: 16

Brand: Haier Pages: 19

Brand: Haier Pages: 18

Brand: Haier Pages: 8

Brand: Haier Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands