ASM AllPro APB2525H Operating Instructions Manual Download | Manualshive

Page: 7 / 24

background image

7

309882

1. Check oil level of engine.

Startup
Always use this startup procedure to ensure that the pressure washer is started
safely and properly.

Always engage gun trigger safety latch when you stop spraying. This reduces the risk of fluid injection or
splashing in eyes or on skin if gun is bumped or accidentally triggered.

Always observe the CAUTIONS in this section to avoid costly damage to pressure washer.

If you use the Sandblaster Kit, see Sandblaster Kit Manual for detailed cleaning information.

.

Operation

2. Check fuel level.

3. Turn on water supply.

Never run pressure washer without wa-
ter. Costly pump damage will result.
Always be sure water supply is complete-
ly turned on before you run pressure
washer.

CAUTION

«
...
5
6
7
8
9
...
»

Summary of Contents for AllPro APB2525H

























Reviews:

No comments

Related manuals for AllPro APB2525H

Lavadora EMW580E3

Brand: EAS Electric Pages: 69

Brand: EAS Electric Pages: 138

Brand: Ryobi Pages: 68

HDS 2.5/20 P Cage

Brand: Kärcher Pages: 40

Brand: Ariston Pages: 36

Brand: Fieldmann Pages: 135

Brand: MAKINEX Pages: 47

Brand: Lavorwash Pages: 16

Brand: Sealey Pages: 4

Brand: AEG Pages: 48

Brand: AEG Pages: 23

Brand: AEG Pages: 44

Brand: AEG Pages: 52

Brand: AEG Pages: 64

Brand: AEG Pages: 40

Brand: AEG Pages: 44

Brand: AEG Pages: 28

Brand: AEG Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands