ASM AllPro APB2525H Operating Instructions Manual Download Page 6 | Manualshive

Page: 6 / 24

background image

6

309882

PRESSURE RELIEF

Follow these instructions whenever you are instructed to relieve pressure, stop spraying for

more than 10 minutes, check or service the equipment, or install or clean the spray nozzle.

1. Engage trigger safety latch

2. Turn pressure washer off

3. Remove ignition cable from spark plug.

4. Shut off water supply. Disconnect from water.

5. Disengage trigger safety latch. Trigger gun to relieve
pressure. Then re–engage the safety latch.

Note:

If you suspect that the spray tip or hose is clogged or that pressure has not been fully relieved after

following the steps above, disengage the trigger safety latch and trigger the gun to relieve pressure.

TI3233A

TI3234a

«
...
4
5
6
7
8
...
»

Summary of Contents for AllPro APB2525H

























Reviews:

No comments

Related manuals for AllPro APB2525H

Brand: Prime Pages: 24

Brand: Hotpoint Pages: 16

Brand: Indesit Pages: 24

Brand: grandimpianti Pages: 85

Brand: GE Pages: 20

Brand: VYKING FORCE Pages: 44

Brand: Smeg Pages: 27

Brand: Hotpoint Pages: 16

HDS 3.0/20-4 EA/EG

Brand: Kärcher Pages: 48

Brand: Kärcher Pages: 224

Brand: Samsung Pages: 80

Brand: Samsung Pages: 44

Brand: Samsung Pages: 11

WF405ATPAWR/AA-0001

Brand: Samsung Pages: 132

Brand: Samsung Pages: 160

Brand: Samsung Pages: 80

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands