ASM AllPro APB2525H Operating Instructions Manual Download Page 16 | Manualshive

Page: 16 / 24

background image

16

309882

Problem

Cause

Solution

Packings are failing
freq entl or

Scored, damaged, or worn plungers

Install new plungers.

frequently or
prematurely

Abrasive material in fluid being pumped

Install proper filtration on pump inlet plumbing.

prematurely

Inlet water temperature too high

Check water temperature. It should not
exceed 104

F (40

C).

Overpressurizing pump

Do not modify any factory–set adjustments.

Excessive pressure due to partially
plugged or damaged tip

Clean or replace tip. See

Installing and

Changing Spray Tips

(page 11).

Pump running too long without spraying

Never run pump more than 10 minutes without
spraying.

Running pump dry

Do not run pump without water.

Strong surging at inlet
and low pressure on
discharge side

Foreign particles in inlet or discharge
valve or worn inlet and/or discharge
valves

Clean or replace valves.

Water spitting out of
thermal valve

Pump running too long without spraying

Trigger gun to get fresh, cooler water in pump.

«
...
14
15
16
17
18
...
»

Summary of Contents for AllPro APB2525H

























Reviews:

No comments

Related manuals for AllPro APB2525H

Brand: Samsung Pages: 5

Brand: Kärcher Pages: 16

Brand: Asko Pages: 16

Brand: Amica Pages: 52

HDEm 2000 Top Line

Brand: Elektro Maschinen Pages: 52

Brand: GE Pages: 96

Brand: Svan Pages: 65

Brand: Kärcher Pages: 32

Brand: V-ZUG Pages: 44

Brand: Blue Clean Pages: 252

Brand: NABO Pages: 32

Brand: Kärcher Pages: 24

Brand: magic clean Pages: 56

Brand: Hotpoint Pages: 16

Brand: Samsung Pages: 44

Brand: VALBERG Pages: 108

Brand: VALBERG Pages: 128

Brand: Frigidaire Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands