background image

14

STERILIZATION:

WARNING

Sterilize the motor

between each patient use.

WARNING 

Use of a sterilization

method or temperatures other than what

are prescribed may damage the motor

or present a risk of cross-contamination

between patients.

CAUTION 

Do not soak or submerge

the motor in any liquid.

STERIlIZATION PROCEdURE:

Pre-clean

1)

Thoroughly brush off any visible signs of

debris from the motor and cord.

2)

Thoroughly clean the device with a moist

cloth or towel to remove any remaining signs

of debris.

Sterilize

3)

Select one of the three following

sterilization methods (A. B. or C.):

Wrapped Sterilization

– 

Place in an

appropriately sized sterilization pouch and

seal it.

A. Gravity Wrapped:

• Minimum Temperature:

132° C (270° F) 

• Full Cycle Time:

20 minutes 

• Minimum dry time:

30 minutes 

B. Prevacuum Wrapped: 

• Preconditioning Pulses: 

• Minimum Temperature:

132° C (270° F)

• Full Cycle Time: 

4 minutes 

• Minimum dry time:

40 minutes 

Flash Sterilization

– For immediate use

only.

C

Gravity Unwrapped:

• Minimum Temperature:

132° C (270° F) 

• Full Cycle Time:

10 minutes 

No dry time is required for flash

sterilization.

MOTOR & CORd ASSEMBly:

• The entire motor and cord assembly is fully

autoclavable. Before autoclaving the

assembly, remove any handpiece from motor

and install autoclaving plugs into the end of

the motor and motor cord connector as

shown below. The plugs are supplied with the

motor and cord.

• Loosely coil the motor cord when auto-

claving.  Avoid sharply bending the cord when

autoclaving.

NOTE:

Call Aseptico, Inc. at 1-800-426-

5913 for any questions or clarifications on

this sterilization procedure.

•  Always install the autoclaving plugs into motor

and motor connector before autoclaving.

•  If the autoclaving plug for the motor becomes

difficult to remove or install, apply silicone grease

or similar lubricant to the O-rings.

Turn black connector ring only

HANdPIECES

Thorough cleaning and

lubrication of handpieces after each use and

before sterilization is very important to ensure

proper operation and service life of the

handpiece. Follow the instructions provided with

the handpiece purchased for complete

maintenance instructions.

CONSOlE MAINTENANCE

The exterior of

the console may be cleaned by wiping with a

soft cloth moistened with mild detergent or

disinfecting solution.

MAINTENANCE & CLEANING:

• Do not attempt to disassemble the motor or motor connector.

• Do not oil or lubricate the motor.

• Do not attach a handpiece to the motor while motor is running.

• Do not bend motor cord sharply.

WARNING

Failure to comply with any of the above instructions may

void your warranty

Summary of Contents for AEU-25





















Reviews: