Notes:
1 .The filter holder should always be
placed in the machine so that it
remains warm. Closed position.
3 .
Only UNO model.
If the coffee does
not come out very hot, press steam
switch
3
for 10 seconds. This will
raise the temperature of the machine
2 .Place the cups on the cup warmer
9
. The right temperature (optimum
40ºC/105ºF) will improve the
espresso. (see picture 6)
3 .Coffee will continue to drip from the
spouts for a moment after the coffee
swich is turned off.
!
THERMOMETER
The thermometer will mark you the
machine temperature. It has to be in
between 80ºC/180ºF and 110ºC/230ºF
for coffee and above 100ºC/212ºF
degrees for steam
!
Important: Tamped
The best espresso result are
obtained when the ground coffee is
firmly tamped.
5-
. Programming the amount
of coffee (TRONIC)
Electronic push-button control functions.
S: small coffee
L: large coffee
XL: non-stop coffee (push button again
to stop flow)
Programming the amount of coffee
With the machine on, push the XL
programming button for 5 or 6 seconds
until the LED flashes.
Push the S small coffee button. The
LED will light up, at the same time the
XL programming LED stops flashing.
Let the coffee flow.
Once you have the desired amount,
push the S again. The machine is now
programmed.
To programme large coffee L, repeat
the operation.
To personalise the amount of coffee
(non-stop), push the XL button. Once
you have the desired amount, push the
button again to stop the flow of coffee.
6-
. Preparation of cappuccino
UNO Mobile filterholder
1 - .Press general switch
1
. Pilots
13
and
6
will come on.
2 . -When pilot 6 goes out, press steam
switch
3
. Pilot
6
will come on.
3.-Wait for light
6
to go out. This
indicates that the coffee machine has
reached its ideal temperature.reached
the ideal temperature.
4-.Turn the hot water/steam knob
4
to
open and allow the first drops of water
to come out. In a few moments, only
steam will come out.
5-.Put the tube
5
into the milk to heat
it so that the milk covers exactly half
the absorption hole (never totally
cover it). Do this for the whole
process. (see picture 7)
6.-Liquid is absorbed through the hole
and cream forms automatically.
The recipient should be lowered
gradually while the milk emulsifies.
7.-Turn the water/steam knob
4
to
closed - and turn off the steam switch
3
.
UNO Fixed filterholder
1 . -Press general switch
1
. Pilots
13
and
6
will come out.
2 . -When pilot
6
goes out, press switch
3
and pilots
6
and
12
will come
on simultaneously and the pump will
be pressed at short intervals.
3 . -Wait for approximately 15 and then
open side knob
4
and let the first
drops of water run out. After a
moment only steam will come out.
Points 5, 6 and 7 are the same as in
the previous section.
DUO VAPOR / TRIO
1-.Turn on the main switch
1
.
On TRIO Model turn on the switch
18
, wait for a 1,5 minues approx. If
the machine was already turned on
(and the TRIO switch
18
- was
already on), pass to step nº 2.
2-.Press switch
3
.The pilot light will turn
on.
3-.You will get steam instantly.
4-.Put the tube
5
into the milk to heat
it so that the milk covers exactly half
the absorption hole (never totally
cover it). Do this for the whole
process. (see picture 7)
5-.Liquid is absorbed through the hole
and cream forms automatically.
The recipient should be lowered
gradually while the milk emulsifies.
6-.Turn off the switch
3
.
If you want a creamy cappuccino, use
cold, fresh, whole milk.
For obtaining micro-foam, you should
maintain the absortion hole in the
same position.
ascaso
ascaso
ENGLISH
ENGLISH
20
21
Picture 6
Picture 5
Picture 7
Get user manuals: