Asante IntraCore 39240 User Manual Download Page 139

Page: 139 / 148

Appendix B: Specifications

The sections below list the features and product specifications for the IntraCore IC39240/480 switch.

TECHNICAL SPECIFICATIONS

Interfaces

- 48/24 RJ-45 connectors for 10/100/100 BASE-T

(Auto-Uplink™) on all ports, Power Saving on all ports.

- 4/2 shared SFP modules for Gigabit Ethernet Interface

- IEEE Auto Negotiation or manual configuration

- Reset button

- RS232 Console port

Status Indicators

- Power Operating status of the unit

- 2/1 LEDs for port link/activity, speed

Performance Specifications

- Forwarding modes: Store-and-forward

- Bandwidth: 96/48 Gbps(non-blocking)

- System Memory: 64MBytes

8000 MAC address with auto-learning and aging

- Less than

20 µs for 64-byte frames latency

- 4 Priority Queue with Weighted Round Robin(WRR) scheduling

- Jumbo frame: 9162 bytes

Single-chip switch fabric non-blocking with on-chip frame buffers

Standard Port Access Control

- IEEE 802.1.W Rapid Spanning Tree Protocol

139

Asante IntraCore IC39240/480

User’s Manual

Summary of Contents for IntraCore 39240





















































































































































Search results

Summary of Contents for IntraCore 39240

Reviews:

Related manuals for IntraCore 39240

Brands by name

Popular brands

Asante IntraCore 39240, User Manual

Search results

Summary of Contents for IntraCore 39240

Reviews:

Related manuals for IntraCore 39240

Brands by name

Popular brands