manualshive.com logo in svg

Asante IntraCore 39240, User Manual

Share
Download
Asante IntraCore 39240 User Manual Download Page 114

 

4) show lldp msap-entry 

This command is used to display msap details information 

Format 

show lldp msap-entry <

1..26

> 

Mode 

Privileged Mode 

10.3.11.7 show logging 

This command is used to display trap records 

1) show logging memory-log 

This command display memory log 

Format 

show logging memory-log 

Mode 

Privileged Mode 

2) show logging flash-log 

This command display flash logs 

Format 

show logging flash-log 

Mode 

Privileged Mode 

10.3.11.8 show monitor 

This command is used to display port mirroring settings 

Format 

show monitor 

Mode 

Privileged Mode 

10.3.11.9 show network 

This command is used to configuration for inband connectivity 

Format 

show network 

Mode 

Privileged Mode 

10.3.11.10 show port 

This command is used to display port mode and settings, display port status 

1) show port port-index 

This command is used to specify an switch interface 

Format 

show port port-index <

port-ID

> 

Mode 

Privileged Mode 

show port all 

This command is used to display all switch interface 

Format 

show port all 

Mode 

Privileged Mode 

10.3.11.11 show port-security 

This command is used to display port security settings 

1) show port-security port 

This command is used to specify an switch interface 

Format 

show port-security port <

port-ID

> 

20 

Mode 

Privileged Mode 

2) show port-security all 

This command is used to display all interfaces’ status 

Format 

show port-security all 

Mode 

Privileged Mode 

10.3.11.12 show rate-limit 

This command is used to ingress and egress rate limit information 

1) show rate-limit port 

This command is used to specify an switch interface 

Format 

show rate-limit port 

<port-ID

> 

Mode 

Privileged Mode 

e.g. Switch#Show rate-limit port 1 
Switch#Show rate-limit port g1 

2) show rate-limit all 

This command is used to display all interfaces’ status 

Format 

show Rate-Limit all 

Mode 

Privileged Mode 

10.3.11.13 show running-config 

114 

Asante IntraCore IC39240/480 

User’s Manual

 

 

Summary of Contents for IntraCore 39240





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands