manualshive.com logo in svg

Asante IntraCore 39240, User Manual

Share
Download
Asante IntraCore 39240 User Manual Download Page 113

 

This command display dot1x and port configuration 

Format 

show dot1x config 

Mode 

Privileged Mode 

2) show dot1x radius 

This command display radius configuration 

Format 

show dot1x radius 

Mode 

Privileged Mode 

3) show dot1x statistics 

This command display dot1x statistics 

Format 

show dot1x statistics 

Mode 

Privileged Mode 

10.3.11.3 show igmp snooping 

This command display IGMP snooping information 

1) show igmp snooping dynamic_router_port 

This command display dynamic router ports information 

Format 

show 

igmp 

snooping dynamic_router_port 

Mode 

Privileged Mode 

2) show IGMP snooping groups 

This command is used to display 

igmp 

groups information 

Format 

show IGMP snooping groups 

Mode 

Privileged Mode 

10.3.11.4 show interface 

This command is used to display summary statistics 

1) show interface history 

This command is used to display port RX and TX 

Format 

show interface history <

port-ID

> 

Mode 

Privileged Mode 

2) show interface statistics 

This command is used to display port summary statistics 

Format 

show interface statistics <

port-ID

> 

Mode 

Privileged Mode 

10.3.11.5 show lag 

This command is used to display link aggregation groups information 

1) show lag lag-index 

This command is used to specify an switch lag 

Format 

show lag lag-index <

port-ID

> 

Mode 

Privileged Mode 

2) show lag all 

This command is used to display all switch lag 

Format 

show lag all <

port-ID

> 

Mode 

Privileged Mode 

10.3.11.6 show lldp 

This command is use to display lldp statistics 

1) show lldp statistic 

This command is used to display lldp statistic 

Format 

show lldp statistic 

19 

Mode 

Privileged Mode 

2) show lldp local 

This command is used to display local information 

Format 

show lldp local 

Mode 

Privileged Mode 

3) show lldp msap 

This command is used to display msap information 

Format 

show lldp msap 

Mode 

Privileged Mode 

113 

Asante IntraCore IC39240/480 

User’s Manual

 

 

Summary of Contents for IntraCore 39240





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands