Arthrex AR-3210-0018 Instructions For Use Manual Download Page 22

Page: 22 / 68

DFU-0332r0_fmt_en-US

Page 18 of 64

2.0

System Installation

and Operation with

Data Input Device

2.1

Installation

1. Your Synergy

Camera Control Unit will

indicate which software configuration is

enabled at boot up on the Video Monitor’s

Splash screen.

2.1.1

Typical System Installation

NOTE: See Typical Interconnect Diagram,

Figure

NOTE: Synergy

may be installed in a tower

or on an equipment boom.

1. Place Synergy

Camera Control Unit (CCU)

on tower shelf or installed on equipment

boom.

2. Attach monitor to the tower or equipment

boom and connect monitor DC power cable

to the rear panel of the monitor as shown.

3. Attach Synergy

Data Input Device to

secondary tower arm or equipment boom.

Connect the cable from the Data Input

Device to the connector labeled “tablet” on
the back of the Synergy

CCU.

4. Connect a Display Port cable to a Display

Port output on the rear panel of the
Synergy

CCU. Connect the other end of

the Display Port cable to the Display Port

input of the display monitor. (3G-SDI or DVI

cables may be used instead of Display Port

cables.) Note: Arthrex recommends

connecting Synergy

to the primary surgical

monitor via multiple output types (e.g.,

Display Port and DVI, Display Port and 3G-

SDI) in the event that one type of connection

is lost.

5. If using a printer, connect the printer cable to

the USB connector on the rear panel of the
Synergy

CCU. Connect the other end of

printer cable to the printer.

6. If using a Synergy Laser Light Source,

connect the laser light source cable from the

laser light source to the connector labeled

“Laser Input” on the back of the Synergy

CCU.

7. Plug the AC power cord into the Synergy

power inlet module and a standard

grounded AC Mains outlet (100-240 V˜, 50-

60Hz).

8. Insert the card edge connector of the

Synergy

camera head into the camera

receptacle on the front of the CCU. Ensure

the camera had connector contacts are clean

and dry prior to insertion.

WARNING: Inserting an incompatible

Camera Head into the camera receptacle

(see Figure 1) can result in damage to the

CCU.

8. Connect the Light Guide cable into the Light

Guide receptacle on the front panel of the
Synergy

CCU. Attach the other end of the

Light Guide cable to the endoscope. If using

a bifurcated light guide, connect the

additional bifurcated light guide connect to

the Synergy Laser Light Source.

9. Insert the endoscope into the Synergy

camera head grasping mechanism or into

the C-Mount Coupler for C-Mount Heads.

10. Press the LED Light Engine On/Standby

Switch to activate the LED light engine.

NOTE

: If there is no Light Guide cable

connected to the Synergy

CCU, pressing

the On/Standby Switch will not activate the

LED light engine until one is connected.

Summary of Contents for AR-3210-0018





































































Search results

Summary of Contents for AR-3210-0018

Reviews:

Related manuals for AR-3210-0018

Brands by name

Popular brands

Arthrex AR-3210-0018, Instructions For Use Manual

Search results

Summary of Contents for AR-3210-0018

Reviews:

Related manuals for AR-3210-0018

Brands by name

Popular brands