ARTEX ELT 1000 Description, Operation, Installation And Maintenance Manual Download Page 5

Page: 5 / 62

ARTEX PRODUCTS / ACR ELECTRONICS, INC.

DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL

ELT 1000 (P/N: A3-06-2749-1)

Y1-03-0259 Rev. U

Company Confidential

Page 5 of 62

ELT D-Sub Plug Installation .................................................................................................. 51

Cockpit Remote Switch 9-Pin Plug Installation ....................................................................... 52

Antenna Connection ............................................................................................................ 52

Cockpit Remote Switch Power Connection ............................................................................. 52

Airframe Ground Connections ............................................................................................... 53

ELT Programming ................................................................................................................ 53

RS-232 Acceptable Nav Data ................................................................................................ 53

ELT Installation and Test ............................................................................................................. 53

Installation .......................................................................................................................... 53

Harness ELT D-Sub Plug Sealing ........................................................................................... 55

Installation Documentation .................................................................................................. 55

Battery Pack Installation .............................................................................................................. 55

Battery Installation and Reinstallation ................................................................................... 55

ILLUSTRATED PARTS LIST ...................................................................................................................... 57

Introduction ................................................................................................................................ 57

Purpose .............................................................................................................................. 57

IPL Usage Guide .................................................................................................................. 57

Manufacturer Name and Address .................................................................................................. 57

Ordering Information ........................................................................................................... 57

APPENDIX A – ELT REGISTRATION ......................................................................................................... 61

Background Information .............................................................................................................. 61

Hex ID Code (15-Hex ID) ..................................................................................................... 61

Registration ................................................................................................................................ 61

Responsibility ...................................................................................................................... 61

Required Information ........................................................................................................... 61

Registration Information Resources ...................................................................................... 61

Where to Register ............................................................................................................... 61

Summary of Contents for ELT 1000































































Search results

Summary of Contents for ELT 1000

Reviews:

Related manuals for ELT 1000

Brands by name

Popular brands

ARTEX ELT 1000, Description, Operation, Installation And Maintenance Manual

Search results

Summary of Contents for ELT 1000

Reviews:

Related manuals for ELT 1000

Brands by name

Popular brands