ARTEX ELT 1000 Description, Operation, Installation And Maintenance Manual Download Page 2 | Manualshive

Page: 2 / 62

background image

ARTEX PRODUCTS / ACR ELECTRONICS, INC.

DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL

ELT 1000 (P/N: A3-06-2749-1)

Y1-03-0259 Rev. U

Company Confidential

Page 2 of 62

This manual includes data for the following equipment:

Component

Part No.

Emergency Locator Transmitter

A3-06-2749-1

2-Wire Remote Switch

A3-06-2759

5-Wire Remote Switch

345-6196

Install Kit, Mounting Tray

A3-06-2758-1

Antenna, Rod (white)

110-338

Antenna, Rod (black)

110-338-01

Antenna, Whip

110-773

Antenna, Blade

110-340

Antenna, Rod (white)

A3-06-2835

Cable, Coaxial, BNC to BNC, 6 ft.

611-6013-04

Cable, Coaxial, BNC to BNC, 12 ft.

611-6013-13

Battery Pack, LiSO2

452-6504-1

External Buzzer

452-6505

PROPRIETARY INFORMATION

This document contains proprietary information and such information may not be disclosed to others for any purpose,
nor used for manufacturing purposes without written permission from ACR Electronics, Inc. (ACR).

Information in this manual is subject to change without notice. ACR Electronics, Inc. makes no warranty, expressed or

implied, with regard to this manual, including but not limited to any implied warranties of merchantability, fitness for a
particular purpose, and non-infringement. In addition, ACR Electronics, Inc. makes no warranty with regard to the

documentation or data contained herein. ACR Electronics, Inc. is not liable in the event of incidentals, special,
consequential, or any other damages in connection with or arising from furnishing, performance, or use of this manual.

Reproduction of this publication or any portion thereof by any means is prohibited. For further information contact
Sales, ACR Electronics, Inc., 5757 Ravenswood Rd, Fort Lauderdale, FL 33312. Telephone (954) 981-3333.

AIRWORTHINESS LIMITATIONS

The Airworthiness limitations section is FAA approved and specifies inspections and other maintenance required under

14 CFR§ 43.16 and 91.403, unless an alternative program has been approved.

IMPORTANT NOTICE

ACR Electronics, Inc. will be responsible for full distribution and revisions of ICA’s (Instructions for Continued

Airworthiness). For inquiries regarding the content and currency of this manual, contact ACR Electronics, Inc., 5757

Ravenswood Rd, Fort Lauderdale, FL 33312. Telephone (954) 981-3333.

«
1
2
3
4
...
»

Summary of Contents for ELT 1000































































Reviews:

No comments

Related manuals for ELT 1000

Brand: S&C Pages: 62

Brand: Alinko Pages: 48

Brand: Monarch Pages: 2

Brand: Kogan Pages: 8

Brand: Yaesu Pages: 80

MAGNETIC Deluxe 1Rw

Brand: YOODA Pages: 2

Brand: Icom Pages: 10

Brand: Daiichi Electronics Pages: 12

Brand: Keller-druck Pages: 2

Portable Transducer

Brand: Humminbird Pages: 2

Brand: DigitaLinx Pages: 8

Brand: Icom Pages: 2

Brand: Icom Pages: 36

Brand: Nautel Pages: 141

Brand: Icom Pages: 44

Brand: Minebea Pages: 34

Brand: THOMSON Pages: 60

Brand: WIKA Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands