ARMTEL IPN-8U User Manual Download Page 3

Page: 3 / 36

IPN-8U NETWORK SWITCHING MODULE

USER MANUAL

armtel.com

page 1/32

[email protected]

ENG

INTRODUCTION

This User Manual applies to various versions of the IPN-8U Network switching mod-

ule ARMT.665200.006 manufactured by Armtel LLC, and is intended to familiarize the User

with the device and the procedure for its operation at the installation site.

IPN-8U Network switching module is part of decentralized digital intercom and Public

address / General alarm communication systems IPN 1.1.

Short name of the product – IPN-8U.
Maintenance personnel for the IPN-8U shall be appointed by the management at the

installation site.

The maintenance personnel shall be required to know the operating procedure of the

IPN-8U to the extent provided for by the User Manual.

Duties of the maintenance personnel shall include maintenance of the IPN-8U in ac-

cordance with this User Manual.

IPN-8U Network switching module is meet the requirements of Technical regulations

of the Customs Union TR CU 020/2011 «Electromagnetic compatibility of technical means».

Summary of Contents for IPN-8U





































Search results

Summary of Contents for IPN-8U

Reviews:

Related manuals for IPN-8U

Brands by name

Popular brands

ARMTEL IPN-8U, User Manual

Search results

Summary of Contents for IPN-8U

Reviews:

Related manuals for IPN-8U

Brands by name

Popular brands