ARM Cortex-M4 Page 88 Generic User Manual Download

Page: 88 / 276

The Cortex-M4 Instruction Set

ARM DUI 0553A

3-41

ID121610

Non-Confidential

3.5.1

ADD, ADC, SUB, SBC, and RSB

Add, Add with carry, Subtract, Subtract with carry, and Reverse Subtract.

Syntax

{S}{

cond

} {

Operand2

{

cond

} {

, #

imm12

; ADD and SUB only

where:

Is one of:

ADD

Add.

ADC

Add with Carry.

SUB

Subtract.

SBC

Subtract with Carry.

RSB

Reverse Subtract.

Is an optional suffix. If

is specified, the condition code flags are updated on the

result of the operation, see

Conditional execution

on page 3-18

cond

Is an optional condition code, see

Conditional execution

on page 3-18

Specifies the destination register. If

is omitted, the destination register is

Specifies the register holding the first operand.

Operand2

Is a flexible second operand. See

Flexible second operand

on page 3-12

for

details of the options.

imm12

Is any value in the range 0-4095.

Operation

The

ADD

instruction adds the value of

Operand2

imm12

to the value in

The

ADC

instruction adds the values in

and

Operand2

, together with the carry flag.

The

SUB

instruction subtracts the value of

Operand2

imm12

from the value in

The

SBC

instruction subtracts the value of

Operand2

from the value in

. If the carry flag is clear,

the result is reduced by one.

The

RSB

instruction subtracts the value in

from the value of

Operand2

. This is useful because

of the wide range of options for

Operand2

Use

ADC

and

SBC

to synthesize multiword arithmetic, see

Multiword arithmetic examples

page 3-42

Summary of Contents for Cortex-M4



















































































































































































































































































Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands

ARM Cortex-M4, Generic User Manual

Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands