manualshive.com logo in svg

ARM Cortex-M4, Generic User Manual

Share
Download
ARM Cortex-M4 Generic User Manual Download Page 224

Cortex-M4 Peripherals 

ARM DUI 0553A

Copyright © 2010 ARM. All rights reserved.

4-8

ID121610

Non-Confidential

Find the IPR number and byte offset for interrupt 

m

 as follows:

•

the corresponding IPR number, see 

Table 4-8 on page 4-7

 

n

 is given by 

n

 = 

m

 DIV 4

•

the byte offset of the required Priority field in this register is 

m

 MOD 4, where:

—

byte offset 0 refers to register bits[7:0]

—

byte offset 1 refers to register bits[15:8]

—

byte offset 2 refers to register bits[23:16]

—

byte offset 3 refers to register bits[31:24].

4.2.8

Software Trigger Interrupt Register

Write to the STIR to generate an interrupt from software. See the register summary in 

Table 4-2 

on page 4-3

 for the STIR attributes.

When the USERSETMPEND bit in the SCR is set to 1, unprivileged software can access the 
STIR, see 

System Control Register

 on page 4-19

.

Note

 Only privileged software can enable unprivileged access to the STIR.

The bit assignments are:

4.2.9

Level-sensitive and pulse interrupts

A Cortex-M4 device can support both level-sensitive and pulse interrupts. Pulse interrupts are 
also described as edge-triggered interrupts.

A level-sensitive interrupt is held asserted until the peripheral deasserts the interrupt signal. 
Typically this happens because the ISR accesses the peripheral, causing it to clear the interrupt 
request. A pulse interrupt is an interrupt signal sampled synchronously on the rising edge of the 
processor clock. To ensure the NVIC detects the interrupt, the peripheral must assert the 
interrupt signal for at least one clock cycle, during which the NVIC detects the pulse and latches 
the interrupt.

When the processor enters the ISR, it automatically removes the pending state from the 
interrupt, see 

Hardware and software control of interrupts

 on page 4-9

. For a level-sensitive 

interrupt, if the signal is not deasserted before the processor returns from the ISR, the interrupt 
becomes pending again, and the processor must execute its ISR again. This means that the 
peripheral can hold the interrupt signal asserted until it no longer requires servicing.

See the documentation supplied by your device vendor for details of which interrupts are 
level-based and which are pulsed.

Table 4-10 STIR bit assignments

Bits

Field

Function

[31:9]

-

Reserved.

[8:0]

INTID

Interrupt ID of the interrupt to trigger, in 
the range 0-239. For example, a value of 

0x03

 specifies interrupt IRQ3.

9

31

0

Reserved

INTID

8

Summary of Contents for Cortex-M4





















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands