ARM Cortex-M4 Generic User Manual Download

Page: 74 / 276

The Cortex-M4 Instruction Set

ARM DUI 0553A

3-27

ID121610

Non-Confidential

3.4.3

LDR and STR, register offset

Load and Store with register offset.

Syntax

{

type

}{

cond

}

, [

{, LSL #

}]

where:

Is one of:

LDR

Load Register.

STR

Store Register.

type

Is one of:

unsigned byte, zero extend to 32 bits on loads.

signed byte, sign extend to 32 bits (

LDR

only).

unsigned halfword, zero extend to 32 bits on loads.

signed halfword, sign extend to 32 bits (

LDR

only).

omit, for word.

cond

Is an optional condition code, see

Conditional execution

on page 3-18

Specifies the register to load or store.

Specifies the register on which the memory address is based.

Specifies the register containing a value to be used as the offset.

LSL #

Is an optional shift, with

in the range 0 to 3.

Operation

LDR

instructions load a register with a value from memory.

STR

instructions store a register value into memory.

The memory address to load from or store to is at an offset from the register

. The offset is

specified by the register

and can be shifted left by up to 3 bits using

LSL

The value to load or store can be a byte, halfword, or word. For load instructions, bytes and
halfwords can either be signed or unsigned. See

Address alignment

on page 3-17

Restrictions

In these instructions:
•

must not be PC

•

must not be SP and must not be PC

•

can be SP only for word loads and word stores

•

can be PC only for word loads.

When

is PC in a word load instruction:

•

bit[0] of the loaded value must be 1 for correct execution, and a branch occurs to this
halfword-aligned address

•

if the instruction is conditional, it must be the last instruction in the IT block.

Summary of Contents for Cortex-M4



















































































































































































































































































Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands

ARM Cortex-M4, Generic User Manual

Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands