Aritech 1X-X3E Series Operation Manual Download Page 19

Page: 19 / 36

1X-X3E Series Operation Manual

Consult your system installer to determine the option configured in your system.

An extinguishing released state is indicated as follows:

• Released LED: Steady.

• Extinguishing Agent Flow LED: Steady, if confirmation is configured.

• Preactivation LED: Steady red, unless extinguishing agent flow confirmation

configured and received, but no extinguishing activation event occurred.

• General Fire Alarm LED: Flashing for detector activation. Steady for MCP

activation.

• MCP Start LED: Steady if the alarm was activated by a start extinguishing

manual call point.

• Extinguishing Sounders On LED: Flashing (for extinguishing activation state)

or steady (for extinguishing in released state) according to your system
configuration.

• Optical Panel On LED: Steady to indicate that the output to activate the

optical warning panel or sign is active.

• Reset LED: Flashing slowly, to indicate that manual reset is disabled until the

configured delay expires.

Fire alarm indications will be on as usual if the extinguishing event that caused
the release was not a start manual call point activation. Fire routing indications, if
configured, are shown in the usual manner, linked to the fire alarm event.

The control panel buzzer sounds continuously.

Faults

Faults are indicated with a flashing General Fault LED and an active fault
indication LED corresponding to the feature or device with a fault.

The control panel buzzer sounds intermittently.

Note:

Contact your installation or maintenance contractor to solve all reported

faults. Some faults can prevent or disable the extinguishing event. See
“Extinguishing event prevented” on page 13 for more information.

Disablements

• A disabled extinguishing event is indicated by a steady General Disable LED

and a steady yellow Preactivation LED.

• Disabled zones are indicated by a steady General Disable LED and a steady

yellow Zone LED.

• Disabled extinguishing sounders (and sounder outputs linked to the activation

or released states) are indicated by a steady General Disable LED and a
steady yellow Extinguishing Sounders On LED.

• Disabled fire sounders are indicated by a steady General Disable LED and a

steady yellow Fire Sounders Delay LED.

Summary of Contents for 1X-X3E Series





































Search results

Summary of Contents for 1X-X3E Series

Reviews:

Related manuals for 1X-X3E Series

Brands by name

Popular brands

Aritech 1X-X3E Series, Operation Manual

Search results

Summary of Contents for 1X-X3E Series

Reviews:

Related manuals for 1X-X3E Series

Brands by name

Popular brands