background image

GB-12

Ignition Switch (988316, 319)

Operate the ignition switch with the removable 
key. The switch uses two positions: Off (1) and 
On (2). To start the engine, turn the key to On 
(2) and pull the recoil handle. To stop the 
engine, turn the key to Off (1).

Throttle Lever

The throttle lever changes the speed of the 
engine. Move the throttle lever to Fast (1) to 
increase engine speed. Move the lever to Slow 
(2) to decrease engine speed.

Choke Control 

Use the choke control to start a cold engine. Pull 
the control out to choke the engine. Push the 
control in when the engine gets warm.

PTO Clutch 

Pull the PTO (power take off) switch past On (1) to Reset (2) 
to engage the mower blades. Push the PTO switch Off (3) to 
disengage the mower blades. 

NOTE: Pull PTO switch to Reset (2) to engage mower 
blades after operator presence control has been released.

Parking Brake

The parking brake holds the tractor in position 
when not in use. 

To engage parking brake, pull the brake handle 
back (1). 

To release parking brake, push the brake handle 
forward (2).

Recoil Starter Handle

Pull the recoil starter handle to start the engine.

Hour Meter

Recoil Start: The hour meter measures the 
number of hours the engine has been run.

Oil Pressure Light (988320)

The red light near this symbol comes on when 
the engine is running and engine oil pressure is 
low. Check oil level and add if necessary. See 
Engine Manual.

Cold Start Disengage

Use the cold start disengage for easier starting on cold days.

1. Pull out cold start chain 1 to 4 links and lock chain in 

frame notch (Figure 5).

2. Start engine and allow engine to warm to operating 

temperature.

3. Slowly release chain from notch.

FILL FUEL TANK

OF1212

OG1180

1

2

OG1190

OE0261

1

2

3

1

2

WARNING: AVOID INJURY. Unit will move if 
steering controls are engaged when cold start 
feature is released.

WARNING: Fuel is highly flammable and its 
vapors are explosive. Handle with care. Use an 
approved fuel container.

NO smoking, NO sparks, NO flames. ALWAYS 
allow engine to cool before servicing.

NEVER fill fuel tank when engine is running or 
hot from operation.

NEVER fill or drain fuel tank indoors.

Replace fuel cap securely and clean up spilled 
fuel.

OG0620

OG0600

Figure 5

OG1320

Cold Start 
Disengage

Notch

Summary of Contents for 988316



























Reviews: