Ariens 926076 Service Manual Download Page 15

Page: 15 / 58

EN – 13

BOTTOM COVER REMOVAL

Remove Bottom Cover

IMPORTANT:

Save all hardware for reinstallation.

Stop engine, remove key and wait for all moving parts
to stop and for hot parts to cool.

Disconnect spark plug wire from engine.

Place unit in service position. See

Service Position

page 7.

Remove hardware retaining bottom cover to frame
and remove cover. See Figure 16.

Install Bottom Cover

Reinstall bottom cover and secure with two tapping
screws and four hex bolts.

Return unit to operating position.

ATTACHMENT DRIVE BELT
REPLACEMENT

Remove Attachment Drive Belts

IMPORTANT:

Save all hardware for reinstallation.

Stop engine, remove key and wait for all moving parts
to stop and for hot parts to cool.

Disconnect spark plug wire from engine.

Remove auger housing. See

Separate Housing From

Frame

on page 7.

Remove attachment drive belts from attachment drive
pulley. See Figure 17.

Install Attachment Drive Belts

Install belts onto attachment drive pulley.

Reinstall auger housing to frame. See

Reinstall Auger

Housing

on page 11.

Adjust attachment clutch / brake. Refer to Operator’s
Manual for adjustment procedure.

IMPORTANT:

Check all adjustments after first use.

WARNING:

AVOID INJURY. Before placing unit

in service position, drain fuel from tank and fuel
system. See

Draining Fuel System

on page 7.

Ensure that unit is secure and will not tip.

Figure 16

WARNING:

AVOID INJURY. Auger / impeller

must stop within 5 seconds when attachment
clutch lever is released.

Figure 17

Summary of Contents for 926076



























































Search results

Summary of Contents for 926076

Reviews:

Related manuals for 926076

Brands by name

Popular brands

Ariens 926076, Service Manual

Search results

Summary of Contents for 926076

Reviews:

Related manuals for 926076

Brands by name

Popular brands