Ariens 926076 Service Manual Download Page 10

Page: 10 / 58

EN – 8

See Figure 4.
6.

Remove hairpin from clevis pin and partially remove
clevis pin from chute control assembly.

Using pliers, compress cable anchor tabs and remove
anchor from chute control assembly.

Guide cable end through hole in control panel.

Reinstall clevis pin into chute control assembly and
retain with hairpin.

IMPORTANT:

Reinstall hairpin into clevis pin so it is not

misplaced.

See Figure 5.
10. Remove hairpin, sleeve bushing and cable eyelet from

deflector arm under control panel.

11. Using pliers, compress cable anchor tabs and remove

anchor from deflector bracket.

IMPORTANT:

Reinstall sleeve bushing and hairpin so parts

are not misplaced.

Figure 4

1. Clevis Pin
2. Cable Anchor
3. Hairpin

Figure 5

1. Sleeve Bushing
2. Hairpin
3. Cable Anchor
4. Deflector Arm
5. Deflector Bracket

Summary of Contents for 926076



























































Search results

Summary of Contents for 926076

Reviews:

Related manuals for 926076

Brands by name

Popular brands

Ariens 926076, Service Manual

Search results

Summary of Contents for 926076

Reviews:

Related manuals for 926076

Brands by name

Popular brands