background image

Subject to change · 40719700 · 1217 · EN

Page 7

www.argo-hytos.com

2.6 

General safety instructions

 

Observe the valid regulations for accident prevention and environmental protection.

 

Observe the safety regulations and requirements of the country in which the product is used / applied.

 

Only use ARGO-HYTOS products that are in technically perfect condition.

 

Observe all instructions on the product.

 

People who assemble, operate, disassemble or maintain ARGO-HYTOS products are not to be under the infl uence of alcohol, 

  other drugs or medications that affect the responsiveness.

 

Only use manufacturer-approved accessories and spare parts, in order to prevent personal danger due to unsuitable 

  spare parts.

 

Observe the technical data and ambient specifi cations specifi ed in the product documentation.

 

If unsuitable products are used or installed in safety-relevant applications, unintended operating states may occur in the application, 

  which can cause personal injury and / or material damage. Therefore only use the product in safety-relevant applications if this use 
  is explicitly specifi ed and permitted in the product documentation.

 

You may only put the product into operation, when it has been established that the fi nal product (e.g. a machine or system), into 

   which the ARGO-HYTOS products have been installed, complies with the country-specifi c regulations, safety regulations and

standards of the application.

2.7 

Product and technology related safety instructions 

      CAUTION

Leaked hydraulic oil
Environmental hazard / risk of slipping.

 

In case of spills, cover the oil-covered surface immediately with an oil-binding medium.

 

 Then immediately dispose of the oil-binding medium according to the national environmental regulations.

Ignition hazard
Risk of electrostatic charge by poorly conducting hydraulic fl uid.

 

 

 

If the electrical conductivity of the hydraulic fl uid is not known, please contact the manufacturer of the 
hydraulic fl uid.

Risk of burns
Contact temperatures according to DIN EN563 (3) and DIN EN13202 (4) may be exceeded during 
operation.

 

Allow the fi lter unit to cool down before touching it.

 

Summary of Contents for CFP 03































Reviews: