background image

39

1. Remove the torx-head screw from

the rear underside of the seat; then

remove the seat.

2. Remove the negative battery cable

and ground wire; then remove the

positive cable.

NOTE: For installing purposes

prior to removing the battery, note
the routing and securing locations of
the cables and harness wires.

3. Remove the two torx-head cap screws

and lock nuts securing the battery

bracket/solenoid to the seat-base; then

move the bracket up and out of the

way and remove the battery.

746-170A

4. Thoroughly wash the battery with

soap and water; then using a wire

brush, clean the battery posts and

cable ends removing all corrosive

buildup. Replace damaged cables or

cable ends.

NOTE: If battery posts or cable

ends have a build-up of white/green
powder residue, apply water and
baking soda to neutralize acid; then
flush off with warm soapy water.

5. Using a multimeter, test the battery

voltage. The meter must read no less

than 12.5 DC Volts for a fully

charged battery.

NOTE: At this point if the meter

reads as specified, the battery may
be returned to service (see step 9).

6. If the meter reads less than specified

voltage, charge the battery using the

following guidelines.
A. When using an automatic battery

charger, always follow the char-

ger manufacturer’s instructions.

B. When using a constant-current

battery charger, use the follow-

ing Battery Charging Chart.

! WARNING

Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to the
state of California to cause cancer
and reproductive harm. Wash hands
after handling.

CAUTION

On the LXR models, make sure to dis-
connect the seat heater harness con-
nector prior to removing the seat.

! WARNING

Avoid spillage and contact with skin,
eyes, and clothing.

CAUTION

Do not charge the battery while it is in
the snowmobile with the battery ter-
minals connected.

CAUTION

Do not remove seal strip on a sealed
battery.

! WARNING

Battery acid is harmful if it contacts
eyes, skin, or clothing. Care must be
taken whenever handling a battery.

CAUTION

Never exceed the standard charging
rate.

! WARNING

An overheated battery could explode
causing severe injury or death.
Always monitor charging times and
charge rates carefully. Stop charging
if the battery becomes very warm to
the touch. Allow it to cool before
resuming charging.

Summary of Contents for M 1100 Turbo





































































Reviews:

Related manuals for M 1100 Turbo