background image

38

NOTE: For installing purposes,

note the side that the servomotor
cables are installed on.

3. Slide each cable drum out of the slot

of the servomotor actuator.

4. While holding the cable housing

firmly, pull the cable as far out as it

will go; then release. Repeat three to

four times. The cable/exhaust valve

should move freely without binding. 

NOTE: If the cable/exhaust valve

does not move freely, the exhaust valve
assembly will need to be removed for
further inspection. Take the snowmo-
bile to an authorized Arctic Cat Snow-
mobile dealer for this service.

NOTE: When measuring the cables,

they are to be routed as close to their
installed position as possible.

5. While holding the cable housing,

lightly pull on one cable end to

remove any slack; then measure the

amount of exposed cable from the

cable housing to the end of the cable

(cable drum).

0735-516

NOTE: The two cable measure-

ments must be equal in length or
less than 0.5 mm (0.020 in.) differ-
ence in length from each other.

NOTE: Repeat steps 4 and 5 for each

cable; then compare the measure-
ments to the APV Cable Length chart.

NOTE: The measurements must be

within the specifications from the
chart. If the measurements are
within specifications, no adjustment
is necessary (proceed to step 8). If
they are not within specifications,
proceed to step 6.

6. Loosen the jam nut on the cable to

be adjusted; then using the adjusting

nuts, lengthen or shorten the housing

as needed.

7. Once the proper length has been

attained, hold the adjusting nut in place

and tighten the jam nut securely.

8. Place the cable housings into posi-

tion in the servomotor. Secure the

cable housings with the cable holder.

Battery (Electric Start)

These sealed batteries after being in ser-

vice require regular cleaning and

recharging in order to deliver peak per-

formance and maximum service life. The

following procedures are recommended

for cleaning and maintaining sealed bat-

teries. Always read and follow instruc-

tions provided with battery chargers and

battery products.

NOTE: Battery maintenance may

be done by the snowmobile owner if
qualified to do so. If the owner does
not feel qualified, take the snowmo-
bile to an authorized Arctic Cat
Snowmobile dealer for this service.
This service is at the discretion and
expense of the snowmobile owner.

To remove and charge the battery, use the

following procedure:

CAUTION

Do not use the nut securing the pul-
ley to the servomotor to rotate the
actuator.

APV CABLE LENGTH 

800 cc

1.377 in. ± 0.039 in.

CAUTION

Assure the cables are rotated and
secured properly to avoid contacting
exhaust components.

! WARNING

Any time service is performed on a
battery, the following must be
observed: Keep sparks, open flame,
cigarettes, or any other flame away.
Always wear safety glasses. Protect
skin and clothing when handling bat-
teries. When servicing battery in
enclosed space, keep the area well-
ventilated.

Summary of Contents for M 1100 Turbo





































































Reviews: