Arctic Cat 2012 350 HS Operator'S Manual Download Page 45

Page: 45 / 80

Divis

ion

- Opera

tion

inte

nance

Use the headlight HI/LO switch to select

the high or low headlight beam when the

ignition switch is in the LIGHTS posi-

tion. When the switch is in the HI posi-

tion, the high beam will illuminate. When

the switch is in the LO position, the low

beam will illuminate. When the switch is

in the Running Light position, the tail-

lights and running lights will illuminate.

Engine Stop Switch

OFF position — The ignition circuit is

off. The engine cannot be started or will

not run. If the engine stop switch is used

to stop engine without turning off igni-

tion switch, the battery may discharge.
RUN position — The ignition circuit is

on. The engine can start and run.

Starter Button

Pushing in on this button activates the

starter motor. Before starting the engine,

make sure the ignition switch is in the

ON position, the transmission is in neu-

tral, and the brake lever lock is engaged.



NOTE: This ATV has safety inter-

lock switches which prevent the
starter motor from activating when
the transmission is not in neutral.

Reverse Override Switch

This ATV is equipped with a reverse

speed limiter system. When additional

RPM is needed in reverse, depress and

hold the override switch



NOTE: On the 425, the reverse

override switch is active in 4WD
only.

Throttle Lever

KC342A

Control engine RPM with the position of

the throttle lever. Operate this lever with

the thumb. Pushing it forward increases

engine RPM and allowing it to retract

decreases engine RPM.

Throttle Limiter Screw

ATV-0053

Throttle lever travel may be limited by

adjusting the throttle limiter screw. The

throttle limiter should be adjusted

according to the operator’s skill and

experience. To adjust the throttle limiter,

use the following procedure.

1. Loosen the jam nut.
2. Turn the throttle limiter screw clock-

wise to decrease engine RPM maxi-

mum or counterclockwise to

increase engine RPM maximum.

3. Tighten the jam nut securely.



NOTE: The ATV is equipped with

an RPM limiter that retards ignition
timing when maximum RPM is
approached. When the RPM limiter
is activated, it could be misinter-
preted as a high-speed misfire.

! WARNING

Never activate the override switch
while the throttle is open as a loss of
control may result.

Summary of Contents for 2012 350 HS

















































































Search results

Summary of Contents for 2012 350 HS

Reviews:

Arctic Cat 2012 350 HS, Operator'S Manual, Page: 45 / 80

Search results

Summary of Contents for 2012 350 HS

Reviews: