manualshive.com logo in svg

Arctic Cat 2012 350 HS, Operator'S Manual, Page: 42 / 80

Share
Download
Arctic Cat 2012 350 HS Operator'S Manual Download Page 42

40

General Information

ATV Identification 

Numbers

The Arctic Cat ATV has two identifica-

tion numbers: Vehicle Identification

Number (VIN) and Engine Serial Num-

ber (ESN).
The VIN is located on the lower-front

crossmember.

KC0055A

The ESN is located on the rear of the

engine crankcase and is visible from the

side.

KC287B

These numbers are required by the dealer

to complete warranty claims properly. No

warranty will be allowed by Arctic Cat if

the VIN or ESN is removed or mutilated

in any way.
Always provide the ATV name, Vehicle

Identification Number, and Engine Serial

Number when contacting an authorized

Arctic Cat ATV dealer for parts, service,

accessories, or warranty. If a complete

engine must be replaced, ask the dealer to

notify Arctic Cat for correct registration

information.

Ignition Switch Key

Two keys come with the ATV. Keep the

spare key in a safe place. An identifying

number is stamped on each key. Use this

number when ordering a replacement

key.

ATV-0055

Control Locations and 

Functions

Ignition Switch

The ignition switch has three positions.

ATV-0056

OFF

 position — All electrical circuits

except the accessory plug are off. The

engine will not start. The key can be

removed in this position.

NOTE: The accessory plug is

powered by the battery at all times.

ON

 position — The ignition circuit is

complete and the engine can run. The key

cannot be removed in this position.

LIGHTS

 position — The ignition circuit

is complete and the headlights and tail-

light are on. The key cannot be removed

in this position.

Summary of Contents for 2012 350 HS

















































































Reviews:

No comments