manualshive.com logo in svg

Arctic Cat 2012 350 HS, Operator'S Manual, Page: 14 / 80

Share
Download
Arctic Cat 2012 350 HS Operator'S Manual Download Page 14

! WARNING

Indicates a potential hazard that could 
result in a serious injury or death. 

12

Warnings

! WARNING

POTENTIAL HAZARD

Operating on steep hills.

WHAT CAN HAPPEN

The ATV can overturn more easily on steep hills than
on level surfaces or small hills.

HOW TO AVOID THE HAZARD

Never operate the ATV on hills too steep for the ATV or
for your abilities.
Practice on smaller hills before attempting larger hills.

! WARNING

POTENTIAL HAZARD

Overloading the ATV or carrying or towing cargo improperly.

WHAT CAN HAPPEN

Could cause changes in ATV handling, which could lead to an accident.

HOW TO AVOID THE HAZARD

Never exceed the stated load capacity for the ATV.
Cargo should be properly distributed and securely attached.
Reduce speed when carrying cargo or pulling a trailer. Allow greater distance for braking.
Always follow the instructions in this Operator’s Manual for carrying cargo or pulling a
trailer.

! WARNING

POTENTIAL HAZARD

Improperly crossing hills or turning on hills.

WHAT CAN HAPPEN

Could cause loss of control or cause the ATV to overturn.

HOW TO AVOID THE HAZARD

Never attempt to turn the ATV around on any hill until you
have mastered the turning technique as described in this
Operator’s Manual. Practice first on level ground. Be very
careful when turning on any hill.
Avoid crossing the side of a steep hill, if possible.

When crossing the side of a hill

:

Always follow proper procedures as described in this Operator’s Manual.
Avoid hills with slippery or loose surfaces.
Shift your weight to the uphill side of the ATV.

! WARNING

POTENTIAL HAZARD

Improperly operating in reverse.

WHAT CAN HAPPEN

You could hit an obstacle or person behind you, resulting in serious injury.

HOW TO AVOID THE HAZARD

Before you engage reverse gear, make sure there are no obstacles or people
behind you. When it is safe to proceed, go slowly.

Summary of Contents for 2012 350 HS

















































































Reviews:

No comments