manualshive.com logo in svg

ARCO LI-2B, Owner'S Manual

Share
Download
ARCO LI-2B Owner'S Manual Download Page 17

   

 

 
 
Solar Wiring Detail 

Step 1 
 
Locate two way terminal connection block on top plate near motor.  This will have Red 
(Positive) and black (Negative) wires.  Connect solar panel direct to it. 
 

 
 
                   Red                                  Brown or Red 
                                                     

+   

                   Black                               Blue or Black 

                                                  - 

           
 

 
IMPORTANT 
 
As a connected solar panel delivers a charge, the solar panel must be covered or 

disconnected when any work or wiring is being done on the control board (other than when 
adjusting trimpots or limit switches) 
 
 
Step 2 

Locate RED wire with spade terminal (Which will be disabled from Positive on Battery).  
Connect this wire and you are ready to set your limits. 
                                                                    
Negative Wire is already connected                                Red Wire to + 

 

Locate Positive Wire (RED) 
Connect RED wire to + on battery     

-       + 

7.2 Amp 

Hour 

SLA 

Batt

 

 

 

 

 
Solar 
Panel

 

          

 

 
 
Note:  All LI-2B gate operator kits (Solar, 240 volt and 12 volt) are supplied complete with a 
7.2 Amp hour battery.  This battery should be checked regularly. 

 

 
 
 
 

 
 
 
 

          

LI-2B Installation Manual

       

Summary of Contents for LI-2B
























Reviews:

No comments

Brands by name

Popular brands

Load more brands