Arcam FMJ A39, Handbook, Page: 7 / 67

E-9 E-8
English
loudspeakers
Normal single wiring
For single wiring, we recommend that you use the
SPEAKER 1
set of terminals on your amplifier. If each
speaker has more than one pair of connecting terminals,
use the terminals labelled
LF
or ‘Low Frequency’.
Connect the red positive terminal of the right speaker
connection on the amplifier (labelled R+ ) to the positive
terminal of your right speaker. Similarly, connect the
black negative terminal of the right speaker connection
on the amplifier (labelled R- ) to the negative terminal
of your speaker. Repeat the process for the left speaker,
using the terminals labelled L+ and L- on the amplifier.
WARNING: If your speakers support bi-wiring, there will be a
strip of conductive metal connecting the low-frequency ( LF )
terminals to the high-frequency (
HF
) terminals; this MUST NOT
BE REMOVED in a single-wired system.
Notes on making speaker connections
< Do not make any connections to any amplifier while it is switched on. We recommend that your
amplifier is completely disconnected from the mains supply before starting.
<
Before switching your amplifier(s) on for the first time after connecting to speakers, please check all
connections thoroughly. Ensure that bare wires or cables are not touching each other or the amplifier’s
chassis (which could cause short circuits), and that you have connected positive (+) to positive and
negative (–) to negative. Be sure to check the wiring for both the amplifier and the speaker.
< After making connections: switch the amplifier on, select a source signal, then gradually increase the
volume to the required listening level.
<
If you are unsure as to how your system should be connected, please contact your Arcam dealer who will
be happy to help you.
Connecting
loudspeakers
There are many different ways of connecting
loudspeakers to your A39. The following section
describes how to connect the speakers and amplifier for
the most common configurations.
PHONO
GROUND
ONLY
PHONO
(MM) CD TUNER SAT BD PVR AV
RECORD
OUT
PRE
OUT
R
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
L
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2 SPEAKER 1
USB 5V / 0.1A
6V 500mA
ACCESSORY
POWER
12V 100mA
TRIGGER
OUT
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
1kW MAX
110-120V/220-240V ~ 50-60 Hz
POWER INLET
LF
HF
LF
HF
R L
Bi-wiring
Bi-wiring is performed in the same way as single wiring
except that, a pair of cables are used to connect the
amplifier to each speaker.
Follow the instructions given for single wiring; then
perform the same actions, this time connecting the
SPEAKER 2 set of terminals on your amplifier to the
terminals labelled HF or ‘High Frequency’ for each
speaker.
WARNING: Speakers that support bi-wiring have a strip of
metal that connects the low frequency ( LF ) terminals to the
high frequency ( HF ) terminals. This MUST BE REMOVED in a
bi-wired system.
PHONO
GROUND
ONLY
PHONO
(MM) CD TUNER SAT BD PVR AV
RECORD
OUT
PRE
OUT
R
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
L
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2 SPEAKER 1
USB 5V / 0.1A
6V 500mA
ACCESSORY
POWER
12V 100mA
TRIGGER
OUT
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
1kW MAX
110-120V/220-240V ~ 50-60 Hz
POWER INLET
LF
HF
LF
HF
R L
Remove metal
strip
Remove metal
strip
Switching on
The POWER button switches the unit on and off.
The power light (next to the ‘POWER/STANDBY’ text)
indicates the state of the amplifier: it changes from red
to orange then green if mains power is connected and
the unit is switched on.
If the unit is left unused for an extended period of time
it will go into standby to reduce power consumption.
Press
AUX
and
BALANCE
to adjust the time of this feature.
Display
The
DISPLAY
button (or
DISP
on the remote control)
changes the display brightness between ‘on’, ‘dimmed’
and ‘off’. If the A39 is powered off with the display
brightness set to ‘off’, the display resumes to ‘dimmed’
when the unit is powered on again.
SAT
Intended for the analogue outputs from a satellite TV
receiver or cable TV box.
BD
Intended for the analogue outputs from a Blu-ray or
DVD-player.
PVR
Intended for the analogue outputs from a Personal
Video Recorder, or similar device.
AV
Intended for the analogue outputs from general audio-
visual equipment, such as a VCR or digital TV/satellite
receiver.
CD
Intended for the balanced analogue outputs from a CD
player or DAC, for example the Arcam D33.
Selecting an audio source
Audio sources may be selected from the front panel
buttons
(PHONO, AUX, CD, TUNER, SAT, BD, PVR, AV)
, or the
remote control
(PHONO, AUX, CD, TUN, SAT, BD, PVR, AV)
.
In each case, the source is selected from the input
sockets with the corresponding name.
Audio inputs
Although the inputs are labelled for specific devices,
all have the same characteristics and each may be
used with any line-level product. The exception is the
PHONO (MM)
input (see page 13 for the specification).
AUX
Intended for the unbalanced analogue outputs from an
Arcam CD player. Note the AUX device page on the
remote will control Arcam CD players by default.
TUNER
Intended for the analogue outputs from an FM, AM or
DAB radio tuner.
Phono input
Phono-level input
The A39 provides a pre-amplification stage to treat
the low-voltage output from a MM (moving magnet)
cartridge. Input specifications are given on page 13.
Output volume is shown on the front display as
PHONO 20 , for example.
Line-level phono input
The phono input may be changed from phono-level to
line-level. Press the front panel PHONO and BALANCE
buttons simultaneously and use the control knob to
change the setting. The front panel display shows
LINE- OFF
(i.e. phono) or
LINE- ON
respectively.
If you wish to use an external phono amplifier, connect
its output to the
PHONO (MM)
input, but make sure that
LINE- ON is selected, since a phono amplifier produces
line-level input.
With the input defined in this way, output volume is
shown on the front display as LINE- 20 , for example.
WARNING: NEVER play a standard line-level source into the
phono input when set to LINE-OFF. This would result in serious
damage to both your amplifier and speakers due to the extra
gain that is applied and would not be covered under warranty.
A39 operation
A39
MUTE DISPLAY BALANCE PHONO AUX CD TUNER SAT BD PVR AV SP1 SP2 AUX PHONES
POWER
POWER / STANDBY