manualshive.com logo in svg

Aqualisa Quartz Electric, Installation And User Manual, Page: 33 / 36

Share
Download
Aqualisa Quartz Electric Installation And User Manual Download Page 33

33

Symptom

Possible cause

Action

Water too hot.

Water flow too low.

a)  Increase the flow by 

turning the water control 

knob towards the cold 

temperature markings 

(anticlockwise) slowly.

b)  Ensure that the stop cock 

and servicing valve are fully 

open. If so, ask the installer 

or the local water authority 

to check that the running 

pressure is above the 

minimum requirement (see 

Pressures section page 

7). This may be apparent 

during periods of high 

demand or when other 

outlets are used.

Spray plate and/or hose blocked 

with scale or debris.

Clean the handset spray plate. 

Remove hose and check for 

restrictions. Run without the hose 

attached to check temperature.

Incoming main water pressure or flow 

too low.

After confirming that the filter is 

clear, check with the installer or local 

water authority.

Seasonal conditions - Warmer 

inlet water temperature.

Set temperature dial to coolest 

setting.

Note: Seasonal water conditions 

influence the temperature range 

of the shower. This applies to all 

electric showers.

Temperature low  Seasonal conditions

During winter months the 

temperature of the incoming mains 

water supply is low. Turn dial to 

warmer setting and adjust spray 

pattern on the shower head.

Summary of Contents for Quartz Electric





































Reviews:

No comments