manualshive.com logo in svg

Aqualisa Quartz Electric, Installation And User Manual, Page: 3 / 36

Share
Download
Aqualisa Quartz Electric Installation And User Manual Download Page 3

3

IMPORTANT INFORMATION

Safety information

This appliance can be used by children aged from 3 years and 
above and persons with reduced physical, sensory or mental 
capabilities or lack of experience and knowledge if they have 
been given supervision or instruction concerning use of the 
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children 
without supervision.
The spray head must be descaled regularly.

This appliance is intended to be permanently connected to the 
water mains and not connected by a hose set.
A suitable double pole isolation switch for supply 
disconnections must be incorporated in the fixed wiring 
circuit, in accordance with current wiring rules. See Electrical 
Installation section for further details. This product must be 
installed by a competent person in accordance with all relevant 
current Water Supply Regulations.
ALL SHOWERS REQUIRING AN ELECTRICAL CONNECTION 
MUST BE INSTALLED BY A QUALIFIED PERSON FOLLOWING 
THE LATEST REVISION OF BS 7671 (WIRING REGULATIONS) 
AND CERTIFIED TO CURRENT BUILDING REGULATIONS.
WITH REFERENCE TO BUILDING REGULATION PART P, 
ANY NEW INSTALLATION OR REPLACEMENT PRODUCT 
INSTALLATION WHICH IS NOT IDENTICAL TO THE 
PRODUCT BEING REPLACED, THE CABLE SIZES, CIRCUIT 

Summary of Contents for Quartz Electric





































Reviews:

No comments