Aquacal 75090 Owner'S Manual Installation And Operation Download Page 25

25

Installing a SuperCell...

1. Clean and dry the electrical terminals on the SuperCell. The contacts must be completely dry to

avoid corrosion and failure of the SuperCell or cable.

2. Tighten the unions by hand for a watertight seal.

3. The SuperCell will have two (2) electrical terminals.

4. The SuperCell cable has three (3) electrical contact terminals, the red weather plug will seal the

unused contact in the cable. Position the SuperCell plug so the two (2) open holes align with the
two mating terminals and push gently, but firmly, to connect.

5. Turn on the system.

6. Check for leaks and proper operation of the chlorinator.

5. Allow the solution to sit in the cell for up to 20-minutes.

6. Safely dispose of the solution; pouring it into the pool is recommended.

7. Remove the cap and rinse the cell with light water pressure; reinspect the cell, and repeat acid

cleaning if the cell is still scaled.

8. Once the cell has been cleaned, dry off the cell electrical terminals; reassemble the manifold,

and return the system to service. CAUTION: The electrical terminals must be completely dry
to avoid corrosion and failure of the cell or cable.

Manual Cleaning of the SuperCell...

1. Turn off circulator pump.

2. Remove the cell and place a cap or plug on the end of the cell as shown.

Plugs are available at any pool supply warehouse or home improvement store.
Ask for a 1.5" MPT clean out plug.

3. Fill the capped cell with water 2-inches from the top of the cell blades.

4. Fill the rest of the cell with Muriatic Acid. This allows for an approximate 1-to-4 solution. Always

add the acid to the water. If you do it the other way around, it can cause the solution to spray
back at you causing serious injury.

Scraping or scratching the titanium blade’s edge or surface will damage the blade catalyst
coating and cause premature failure of the cell... warranty will be voided. Never use any sharp
or metallic objects to remove scale.

Failure to heed the following may result in equipment
damage.

CAUTION !

MAINTENANCE

CHEMICAL HAZARD... To avoid damaging splashes, always add acid to water, never water to
acid. Wear safety glasses and use other appropriate personal protection equipment.

Failure to heed the following may result in permanent
injury or death.

WARNING !

Summary of Contents for 75090

































Reviews: