APRILIA 8140172 Service And Repair Manual Download | Manualshive

Page: 92 / 279

background image

ENGINE

3

- 9

RSV mille

◆

Unscrew and remove the screw (5) and disconnect the
cable from the “neutral” gear switch (6).

◆

Move the protection element (7) aside and disconnect

the cable from the engine oil pressure sensor (8).

◆

Move the protection element (9) aside, unscrew and re-
move the nut (10), recover the washer and disconnect
the starter motor cable.

◆

Remove the rear brake lever and relevant mount (11),

see 7.1.46 (REMOVING THE REAR BRAKE LEVER).

a

CAUTION

Move the mount (11) and secure it in place, taking ex-
treme care as it remains connected to the electric ca-
ble by means of the brake light switch (12).

◆

Remove the rear brake pump (13), see 7.6.4 (REMOV-
ING THE BRAKE PUMP).

a

CAUTION

Move the rear brake pump (13) and secure it in place,
taking extreme care as it remains connected to the
brake fluid pipes.
The brake fluid tank (14) must be held vertically to
prevent the fluid spilling out.

◆

Remove the clutch control cylinder, see 3.2.3 (REMOV-
ING THE CLUTCH CONTROL CYLINDER).

◆

Remove the drive pinion, see 7.1.51 (REMOVING THE
DRIVING CHAIN SHOE).

◆

Remove the gearshift lever, see 3.2.2 (REMOVING

THE GEARSHIFT PEDAL).

◆

Remove the expansion tank, see 5.9 (REMOVING THE
EXPANSION TANK).

«
...
90
91
92
93
94
...
»

Summary of Contents for 8140172
























































































































































































































































































Reviews:

No comments

Related manuals for 8140172

Brand: Uclear Pages: 2

Brand: KEEWAY Pages: 164

Brand: BMW Pages: 139

Brand: TVS Pages: 60

Brand: Baja motorsports Pages: 66

Brand: yasuni Pages: 8

Brand: DYNATEK Pages: 13

990D0-E5500-000

Brand: Suzuki Pages: 10

Brand: Montesa Pages: 114

4Ride MST260 2016

Brand: Montesa Pages: 158

Brand: R&G Pages: 6

Brand: Innovv Pages: 2

Brand: Yamaha Pages: 11

Brand: Yamaha Pages: 43

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands