APPLIED ACOUSTICS 1082 Operation Manual Download Page 45

Page: 45 / 48

1082 Smart Switch Operation Manual

CHA-1082-8000/11

__________________________________________________________________________________________________________

Page

13. Appendix C Firmware Update Instructions

Required:



1082

Smart

Switch.



PC with serial com port and “Smart Switch Programmer” software installed.



Latest version of software (hhXXX.ss.hex).



RS232 serial cable (1 to 1, not crossover cable).

Instruction:

1. Connect 1082 Smart Switch to PC com port via serial lead.

2. Run “SmartSwitchProgrammer.exe”. The software will automatically start searching for a

connected Smart Switch. (The software will automatically use the com port that was last
used with the software, if this is incorrect, please select correct com port from the menu)

3. Reset the Smart Switch

Summary of Contents for 1082

















































Search results

Summary of Contents for 1082

Reviews:

Related manuals for 1082

Brands by name

Popular brands

APPLIED ACOUSTICS 1082, Operation Manual

Search results

Summary of Contents for 1082

Reviews:

Related manuals for 1082

Brands by name

Popular brands