manualshive.com logo in svg

Applanix POS MV V5, Installation And Operation Manual

The Applanix POS MV V5 is an advanced positioning and orienting system featuring cutting-edge technology. To effectively install and operate this product, users can access the comprehensive Installation And Operation Manual. Download this manual for free from our website manualshive.com, ensuring seamless utilization of the Applanix POS MV V5 system.

Share
Download
background image

POS MV V5 Installation and Operation Guide 

Interfaces

 and Data Formats

 

 

Copyright  ©  Applanix Corporation, 2017 

 

3-1

 

3.0  Interfaces and Data Formats 

This section of the manual describes the data formats for each of the following interface ports on the POS 
Computer System (PCS) rear panel. 

Note: 

Each port has a different format. To avoid operating problems, give careful attention to the 

structure of each interface. 

LAN (Ethernet) Data 

The POS MV 10/100BaseT Ethernet interface conforms to the Institute of Electrical and Electronics 
Engineers (IEEE) 802.3i standard. It allows you to configure the system and to monitor its status during 
operation. 

The interface comprises four ports: 

•

 

Control port - used to transmit configuration information to POS MV 

•

 

Display port - provides navigation and attitude information at a low update rate for use by the MV-
POSView Controller program running on a separate PC 

•

 

Real-time data port - provides user selectable navigation and attitude data, at higher update rates 
with minimal latency, for use by other computers on a shared Ethernet LAN 

•

 

Logging data port - provides user selectable navigation and attitude data, at higher update rates  
but is buffered for robust logging by other computers on a shared Ethernet LAN 

POS MV broadcasts information from the display port using the Universal Datagram Protocol (UDP) 
protocol and outputs data on the logging data port using the Transmission Control Protocol (TCP) 
protocol. For the real-time data port the protocol can be selected from UDP, UDP Unicast or TCP. 
Information is organised into a data group structure and each port may be configured independently to 
permit the output of selected data groups. 

The MV-POSView Controller program configures the groups transmitted through the display port 
automatically according to the specific windows that the program has open at any one time. The group 
structure is therefore user transparent. POS MV enables groups automatically to support the demands 
that you make by opening windows within the controller program. 

COM Ports 

The five RS-232 serial ports, COM(1) through COM(5), allow communication between the PCS and 
external equipment. Two of the five COM ports are software switchable between the RS-232 and RS-422 
protocols. Two of the five COM ports are software switchable to connect with the internal GNSS receiver 
COM ports. All COM ports are assignable for input and/or output. The following identifies the available 
port assignments: 

Summary of Contents for POS MV V5




































































































































































































































































































Reviews:

No comments

Related manuals for POS MV V5

Jansite T10 Installation Manual preview
T10
Brand: Jansite Pages: 28
Boss Audio Systems BV9974B User Manual preview
BV9974B
Brand: Boss Audio Systems Pages: 16
XZENT X-402 User Manual preview
X-402
Brand: XZENT Pages: 52
Xomax XM-DTSB930 Installation Manual preview
XM-DTSB930
Brand: Xomax Pages: 34
Xomax XM-2VRSUA738 User Manual preview
XM-2VRSUA738
Brand: Xomax Pages: 34
VDO CD 5626 X Specification Sheet preview
CD 5626 X
Brand: VDO Pages: 2
AQUAJOE SJI-TLS20 Quick Manual preview
SJI-TLS20
Brand: AQUAJOE Pages: 16
InCarTec r.LiNK 27-311 Manual preview
r.LiNK 27-311
Brand: InCarTec Pages: 17
Logic MBN51 Manual preview
MBN51
Brand: Logic Pages: 23
Volvo 31285224 Installation Instructions Manual preview
31285224
Brand: Volvo Pages: 71
Porsche PCM3.1 Operating Manual preview
PCM3.1
Brand: Porsche Pages: 206
Chevrolet 2015 Captiva Sport Owner'S Manual preview
2015 Captiva Sport
Brand: Chevrolet Pages: 89
Vais Technology GSR-04X Owner'S Manual preview
GSR-04X
Brand: Vais Technology Pages: 14
MP L350D-2 Installation And Maintenance preview
L350D-2
Brand: MP Pages: 4
jockey AVANO Prelude 80 Instructions Manual preview
AVANO Prelude 80
Brand: jockey Pages: 36
RadioPRO RP5-GM31 Instruction Manual preview
RP5-GM31
Brand: RadioPRO Pages: 5
Holux NAV-62E User Manual preview
NAV-62E
Brand: Holux Pages: 57
Holux GPSmile 55 Pro Series User Manual preview
GPSmile 55 Pro Series
Brand: Holux Pages: 56

Brands by name

Popular brands

Load more brands