manualshive.com logo in svg

Applanix POS MV V5, Installation And Operation Manual

The Applanix POS MV V5 is an advanced positioning and orienting system featuring cutting-edge technology. To effectively install and operate this product, users can access the comprehensive Installation And Operation Manual. Download this manual for free from our website manualshive.com, ensuring seamless utilization of the Applanix POS MV V5 system.

Share
Download
background image

POS MV V5 Installation and Operation Guide 

Installation 

 

 

2-32

 

•

 

-5° for the IMU with respect to reference frame x mounting angle 

IMU with respect to Reference Frame 

Measure and record the rotations that you must apply, using the Tait-Bryan sequence explained above, to 
align your chosen reference frame with the IMU reference frame. 

Sensor 1 with respect to Reference Frame 

Sensor 1 is typically a multibeam transducer. Measure and record the rotations that you must apply, using 
the Tait-Bryan sequence explained above, to align your chosen reference frame with the sensor 1 frame. 

Sensor 2 with respect to Reference Frame 

Measure and record the rotations that you must apply, using the Tait-Bryan sequence explained above, to 
align your chosen reference frame with the sensor 2 frame. 

Note

:  If your application does not use a second sensor, record these mounting angles as zero. 

Installation Checklist 

This checklist is included to help you install the POS MV efficiently and with minimal disruption to the 
vessel, its crew or any ongoing operations. 

After installing the system correctly and all items have been checked against this list, refer to the 
Interfaces and Data Formats description starting on page 3-1 to configure and start using the POS MV. 

1. Mechanical 

Interface 

a) IMU 

Positioning: 

 

Mount the IMU as close as possible to the multibeam transducer. 

 

Mount the IMU rigidly so that it cannot move or rotate 
independently of the vessel. 

 

Install the IMU where the data and power cable will reach easily 
between the IMU and the PCS. 

 

Ensure there is sufficient clearance for the connectors at both 
ends of the data and power cable. Tighten the connectors by 
hand only. 

 

Mount the IMU so that it is approximately level. 

 

Do not immerse the IMU in water or any liquid. 

 

Respect the environmental limits listed for the Inertial 
Measurement Unit on page 2-4 for storage and operation. 

 

Refer to the Drawings section on page E-1 for dimensional 
details to help when you install the IMU. 

 

Connect the IMU housing to a good ground connection. 

Summary of Contents for POS MV V5




































































































































































































































































































Reviews:

No comments

Related manuals for POS MV V5

Senju Sprinkler ZN-RES Manual preview
ZN-RES
Brand: Senju Sprinkler Pages: 8
Rain Bird isa 300/400 Installation, Programming, And Operation Manual preview
isa 300/400
Brand: Rain Bird Pages: 45
NavLinkz r.LiNK DVD 800 Manual preview
r.LiNK DVD 800
Brand: NavLinkz Pages: 19
TOP VEHICLE TECH KWBMW11 Installation Manual preview
KWBMW11
Brand: TOP VEHICLE TECH Pages: 8
flexvision LCM1210 Owners & Installation Manual preview
LCM1210
Brand: flexvision Pages: 13
FCA US Uconnect 3 2018 Manual preview
Uconnect 3 2018
Brand: FCA US Pages: 66
Viking MICROFAST VK337 Bulletin preview
MICROFAST VK337
Brand: Viking Pages: 8
Viking MICROFAST VK311 Technical Data Manual preview
MICROFAST VK311
Brand: Viking Pages: 8
VDO MCF 5401 - Datasheet preview
MCF 5401 -
Brand: VDO Pages: 2
Toyota TNS400 Owner'S Manual preview
TNS400
Brand: Toyota Pages: 270
Streamax Smart Pad User Manual preview
Smart Pad
Brand: Streamax Pages: 11
K-Rain RPS Select Setting Instructions preview
RPS Select
Brand: K-Rain Pages: 2
K-Rain R-200 Installation Manual preview
R-200
Brand: K-Rain Pages: 2
B52 Geo43 User Manual preview
Geo43
Brand: B52 Pages: 29
ZENEC ZE-NC4110 - MOUNTING INSTRUCTIONS FOR SANTA... Installation Instructions Manual preview
ZE-NC4110 - MOUNTING INSTRUCTIONS FOR SANTA...
Brand: ZENEC Pages: 6
NavLinkz VL1-MBN4 Manual preview
VL1-MBN4
Brand: NavLinkz Pages: 18
Datron DBS-4500 - REV A Manual preview
DBS-4500 - REV A
Brand: Datron Pages: 18
Harman Infinity 6532ix Installation Manual preview
Infinity 6532ix
Brand: Harman Pages: 13

Brands by name

Popular brands

Load more brands