background image

The led will now be solid red. 
Switch controller off. 
As simple as that. 
 

To calibrate the drone

Switch controller and drone on. 
Flick SWB from position 1 to position 2 four times. 
The rear white LED’s on the drone will come on. 
On a flat level surface rotate the drone 6 times clockwise (mine seems to only need 3 
rotations but the original manual says 6). The white led should now flash intermittently. 
I then point the drone nose down and rotate it again, but the manual does not call for this. 
Place again on a flat level surface 
The white LED's should now not be on and it will be only the red, green and blue eye lights 
once more.  
Switch everything off. Calibration now complete. 
 

GPS Lock:  

DO 

NOT

 try to fly at all for the first few minutes of the first flight, find a nice open space, 

switch the controller and drone on and put them both down, take a few steps away and 
don't touch them. The red lights on the controller should all go off on their own, especially if 
you are a few paces away, your body can partly block the gps signal and slow down a gps 
lock, have patience.  
 

Note

: Be gentle with it on the first flight, get used to the controls by doing simple 

manoeuvres such as short point to point take off and landings, slow banked turns etc. and 
try to resist the urge to go full throttle. 
 

 

Summary of Contents for CG035






























Reviews: